montecarloss

iTrader: (19)

Has anyone used the holley oil pan in their g-body?I have hummer pan on my car and it scrapes over bumps.any pic and performance point of view will be helpfull.

NBM-WU8

iTrader: (2)

I can try to get you some pictures of the Holley pan in our '88 SS when I get a chance. Can't tell you much from a performance standpoint since we haven't got the car running yet though.

the_merv

iTrader: (88)

How low is your car? Mine hasnt scraped on anything..hopefully it doesnt..but then again I'm not slammed.

montecarloss

iTrader: (19)

NBM-WU8 thanks man

the_merv, I have drop spindels up front and lower spring on back.With the 6.0 and the magnacharger it seats very low.look here
https://ls1tech.com/forums/conversio...nacharger.html

the_merv

iTrader: (88)

Ya you are lower than mine..good lookin car.

NBM-WU8

iTrader: (2)

Here are the pics Monte. Sorry some of them are dark but it should give you an idea. Keep in mind these are using the BRP Mounts...







With a straight edge on the crossmember, the sump of the pan sits about 1/2" above the crossmember.

the_merv

iTrader: (88)

That's pretty nice..

Here is the H3 Pan..Conversion Plates, stock Mounts & Clamshells.



I'm goin to eventually weld up a 1/4" steel skid plate..how much was the Holley one? Specs?

NBM-WU8

iTrader: (2)

I believe it was around 350 when we bought it but I don't remember exactly. Holds 6 quarts with filter.

LS1MCSS

iTrader: (18)

This car has the Holley pan on an LY6. I am pretty sure that it's no lower than the cross member.

http://smg.photobucket.com/albums/v3...1150819_1_.mp4

llorracs93s10

iTrader: (5)

Damn, I think I am going to get me the holley pan....Merv, thats too low for my tastes. I like my cars low, and id scrap my pan on this bump which resides right outside my house....lol

montecarloss

iTrader: (19)

NBM-WU8, those are some perfect pic man.am going to buy a holley pan.
the_merv ,that's how my hangs
LS1MCSS,that's a nice build and good hp on manifolds

montecarloss

iTrader: (19)

NBM-WU8, do you have the part #'s for the pickup tube and oil dipstick?

NBM-WU8

iTrader: (2)

Pan comes with the pickup tube. Requires use of LS3 dipstick (GM P/N 12634547) and tube (GM p/n 12625031) (taken from holley website)

Also, here are the install instructions.http://holleyparts.net/data/Products...R10566rev2.pdf
It will require a new windage tray unless you want to cut yours up to make it fit

montecarloss

iTrader: (19)

thanks again

01cherryreds10

iTrader: (9)

Thanks very much for the pictures I think I'm gonna get the holley pan as well and sell the musclecar one

Screamer27

iTrader: (2)

I'm running the CTS-V pan, I had to notch the cross member, but I hang as far down as the Holley Pan. I'll try to get pics tonite.

the_merv

iTrader: (88)

I guess it's the way the Cradle is shaped in these cars..I use the same pan in my S10 and the bottom of that H3 Pan is flush with the Cradle..

uneek1976

What's the difference between the holley, h3, and the gm muscle car pan?

the_merv

iTrader: (88)

H3 and the GM Muscle Car Pan are the same thing, the Holley shows the difference in the pics..and from what I've read about $200 more easily.

T76s10

iTrader: (6)

Isn't the ctsv pan supposed to be the best choice for g bodys?