penningta

iTrader: (3)

Here is my build. I'm curious to see what you guys think it will make power wise and what the car will run.

Motor is a 6.0 .030 over.
Stock crank
Callies h beam 6.125 rods
Je asymmetrical 11.1 cc dome pistons
Prc ls3 cnc heads with ti retainers and dual 650 lift springs. They are supposed to flow 340 ish at 600 lift I believe
Super vic intake
Cammotion hydraulic roller 245/252 621 612 111 lobe sep 108 int c/l
Morel ls high rpm race hydraulic roller lifters
Brian tooley ls3 trunion upgraded cyro coated and polished rockers
750 carb on 112

Car is a 2800 lb fox body with a glide and 28 10.50 15 slicks
probably around a 5000 stall. Havnt had it built yet. Car went fastest at 10.13 on old sbc 355 setup. It made 525 hp on dyno. This is flywheel hp

one fast zo6

iTrader: (490)

525whp 9.80et

CAMMOTION PERF

Looks like a solid 9 second combo. When will this be on the track?

penningta

iTrader: (3)

As soon as you ship out my cam!! HAHAH just kidding. Just got a call 2 days ago that you are out of cam cores. I hope to get the motor pretty much assembled next weekend so I can messure for push rod length. Then its off to the dyno so I can get my converter built. Hope to be at the track in 2 months!!!!!


Compression is going to be right around 13.1-13.2 compression. SHould make for a solid combo

CAMMOTION PERF

Yes sir. We were waiting on the newest batch of 8620 cores to come back from heat treating. A batch came in on Thursday and we are prepping them to be ground now. Give Danny a call on Monday and we will see if we can get yours going ASAP.

penningta

iTrader: (3)

Will do. Thanks again. From the pics Ive seen of these 8620 cores they almost look to nice to put in a motor!!

penningta

iTrader: (3)

HE said I should have it Friday!!!!!

penningta

iTrader: (3)

What oil would you guys recommend for break in of this combo. Lifters say nothing heavier then 5w40. I was going to run 5w40 Schaffer synthetic oil. But have heard many times not to break a engine in on synthetic

Zmg00camaross

iTrader: (11)

Regular ole carquest 5w30

penningta

iTrader: (3)

DYNO results

Jimbo1367

Good Numbers. 600+ dam

speedtigger

iTrader: (16)

Look how the power just carries. It just goes and goes.

penningta

iTrader: (3)

Yeah and his dyno is a true dyno. What it says is pretty close to what it is. If you take hp to weight calculators. It's almost spot on to what my old setup made when I had it done there

CAMMOTION PERF

Good work. I bet it is going to rip up the pavement.

Mr Monaro

I was going to add top notch service with commotion Kip and crew very happy.
cheers
joe

SSZ

Nice work by Cammotion for coming through on the cam. Its good to see sponsors coming through like that.
Interested to see WHP and track results. Good luck and nice numbers. Like Speedtiger said, talk about the power hanging in there!!!

penningta

iTrader: (3)

Well I finally made it to the track!!!! Converter is a little to tight. Its flashing about 700 rpm lower then I would like it to> Hopefully thats whys its slower then I thought it would be. But still felt good to be back in the seat. Got a little rust to get figured out on the tree again. .005 light but on the wrong side in this pass. Damit.
Car went 10.11 in my only 1/4 mile pass with trans brake at 3500rpm. 1.426 40ft with 6.429 @106.99 Next pass was trans brake at 4700rpm went 1.414 60ft 6.395 @107.56 1/8. Clicked it off. Started raining at 1/8 mile. Only one more pair went down after me.
Here is a link to vid of last pass
https://video-dfw1-1.xx.fbcdn.net/hv...43&oe=55D6501D

penningta

iTrader: (3)

the links only work for a few hours and stop. I give up