Z06PSI

iTrader: (33)

Here are a few pictures of the beginning of the install. This is going on a stock LS6 until the new Forged LS6 is built next month and then installed in April or May.




Looks like something was living under there.....


Thats better.

This is all for this afternoon as I have social event to go too.



More to come tonight.....!!!!!!!!!

Johny GTO

can u measure how far off the ls2 that the blower sits? How high, how far back, forward, etc.

barnat

iTrader: (59)

Whered all the grass & dirt &**** come from??LOL!!

Superman09

iTrader: (65)

Pull yours off and i bet you find the same, haha.

Looking great so far man, the KB should rip and sound KILLER!

NHRAMAN

iTrader: (1)

MURDERSS.........Should be cool.....

Z06PSI

iTrader: (33)

I need to change my name don't I?

The inside of the heads are extremely clean though and thats all that matters. Going downstairs to continue......

Blkss13

Sweet! Can't wait for more pics!

NHRAMAN

iTrader: (1)

NAHHHHHHH.!!!!!!!! Although alot don't get it i bet. [ 1 st time i heard that was in 1979 in S.KINGS..THE SHINING MOVIE.]

GrnDragon

iTrader: (4)

I need to hear some real world results about this Blower before I make the big purchase! By real world results, I mean street driving and etc, more than just dyno numbers.

Z06PSI

iTrader: (33)

Well here is a mock up....












THIS THING IS ******* HUGE..........................!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!

This is not for an F-body. It is the 2.8L Big Bore and honestly a 2.2L or maybe even a 2.6L but not this one. Look......







I have to relocate the power steering pump and clearance the only nice valve covers that will fit. I have three sets and these old C5R covers fit with a little massaging.

edcmat-l1

iTrader: (10)

Hey Andrew. Looks good. Do you have a baseline tune? Lemme know.

Z06PSI

iTrader: (33)

No I do not Ed. I was actually thinking about that tonight. I don't want to compound the install with the addition of the the cam as well but it is tempting.

Johny GTO

i want one on my GTO very badly.

edcmat-l1

iTrader: (10)

I can tell you first hand they have incredible torque at the hit of the throttle.
Tuned one that had 600 ft lbs at 2200 rpms. It was nothing short of brutal. And when you get the drag radials hot, it'll roll the eyes back in your head!!LOL

edcmat-l1

iTrader: (10)

You ought to baby it on down here, and we'll get it dialed in. Then we can retune after the forged motor goes in. You wont have to pay for 2 tunes.
Be best to make sure its safe for a while.

Z06PSI

iTrader: (33)

I have a trailer so I can get it down there regardless. Might not be too fun putting it on the trailer though.

edcmat-l1

iTrader: (10)

Check out the before and after numbers. This was previously tuned by a "leading tuner" (1 bar MAF)LOL. My 2 bar SD tune is richer down low, and still made a **** load more power.
How bout that torque curve?!

CHarris

iTrader: (5)

Looking good!

I'm loving my Kenne Bell 2.8L H series. I'm finally able to start using the higher boost capability of the blower since I had some custom pulleys made for the trucks. I think we're going to start seeing a lot more Power in the Kenne Bell platforms now

Here's a pic of the new custom pulley on my H2. If anyone needs custom pulleys I can direct you to a great shop that will make them better than Kenne Bell does

edcmat-l1

iTrader: (10)

Hey Cory. You got a LS7 manifold? I need one Monday. Can you ship it out first thing monda? Lemme know and I'll paypal the money tomorrow.
OOPS, sorry for the hijack Andrew!!

Z06PSI

iTrader: (33)

Hey no problem. I am not sensative as the mods are here.