Magred2001vette

iTrader: (2)

For my cam only setup w/ headers and labor on a '01 vette I spent...$3564

cam 395
comp pushrods 114
dual springs/tit. retainers/harden seats/valve seals 295
professional labor on cam 495
full dyno tune 200
....................................Total $1499 basic cam only package

Extras:
comp adj. timming chain needed to degreee cam 175
additional to degree cam 50
ASP pully w/ belts 175
new o2 sensors (for best readings) w/ extensions 150
...................................Total $550 extras not needed for basic install

LG long tube headers w/ full stainless 3'' x-pipe exhaust 1200
new gaskets 20
professional labor on headers 295
...................................Total $1515

I NEVER intended to spend this much, but one thing led to another...lets hear your thoughts and opinions on your cam setups.

HumpinSS

iTrader: (1)

912 for cam PR, gaskets, springs, seats, retainers and locks.

156 foroil pump and new o-ring
86 for double roller
100 for valve spring compressor
0 for labor (done by me and my father)

99 Pewter TA

iTrader: (38)

cam=200 used
springs=150
retainers=150
push rods=109
timing chain=50
install=300
total=959

Magred2001vette

iTrader: (2)

sounds like I'm inline with everyone for the basic cam install

foff667

iTrader: (2)

Heads-1000
Cam-300
PR's-120
Gaskets & bolts-135
Food & drink in exhange for install help-70
Total=1625

General Jack

iTrader: (4)

About $2,600.

$1,000 for coated long tubes + ORY + O2 sims, etc. + $150 to a guy to help with install.
$1,600 to MTI for cam + valvetrain + install + tuning.

Sounds like a wet dream now too!

smithsc

T-Rex Cam $400
Comp921 Spring Kit $560
TR Hardened Pushrods $110
ASP Pulley $245
Rollmaster Dual Row Chain $100
Kooks 1 7/8" Headers (no cats) $1200
TR55IX Plugs $55
MSD Wires $60
Misc. tools, gaskets, belts, etc. $300

Labor $0.00 (just a lot of scraped knuckles)

Total $3000 (+/-)

Wished I hadn't added it up now!!

Steve

Bull_in_a_china_shop

iTrader: (1)

cam, pushers and 918's were on special from speed for $780 i think.

installed ourselves

SSCamaro99_3

iTrader: (1)

Hotcam Kit - $300
Katech Oil Pump - $120
Timing Set - $100
Thermostat - $45
ASP Pulley - $200
Gaskets - $50
LS6 Intake - $350
Fluids - $25

About $1200.

pdd

iTrader: (3)

cam-400
hardend rods- 100?? i forgot
lg long tube headers with high flow cats-1800
new gaskets 100
oil pump-150
double roller-100
2650
labor-free i did all the wrenchin

P Mack

iTrader: (6)

380 - cam, 918's, titanium retainers (used)
100 - double roller timing chain
130 - ported ls6 pump
110 - pushrods
30 - gasket kit
40 - coolant, crank bolt, o-ring, loctite, lifter tool, etc
0 - labor
---
790 total

There's also $1000 for Kooks Stainless 1 3/4 and y-pipe and $500 for HP tuners.

glen

iTrader: (1)

Four Cams, two sets of heads both ported professionally, one set of springs and Ti retainers, 2 sets of PR's, one and half sets Roller Rockers, 2 sets off the shelf headers one set custom made all coated, 3 complete exhuasts 2 w/X pipe, 2 TC, 2 rebuilt engines, all installed by me. Don't wanna know the price.

Krab

iTrader: (28)

A quarter short of $770 for a Thunder Racing cam package (cam, pushrods, retainers, springs) with a complete gasket set and set of NGK's, and about $70 for a double roller timing chain. Installation was free (did it myself), and tuning was another $300. Total cost was $1140 for everything. Man, now I too wish I hadn't added it all up. This is an expensive hobby.

01_SuperSlow

iTrader: (7)

cam $ 400
timing chain $ 100
oil pump $ 85
pushrods $ 115
springs $ 260
gaskets $ 40
headers $ 650
custom y and cats $ 330
pulley $ 260
custom tune $ 300
labor $ 0 but lots of scratches and bloody knuckles

total $ 2540

93octane

I am in the process of getting all of the parts for a cam swap, and I don't even want to think about it.

97M6Formula

iTrader: (6)

this is why I went back to the lt1....I did cam, fluids, roller rockers, valvesprings, hardened pushrods, timing chain, ported and polished my own heads, 3 angle valvejob, gaskets, long tube headers, for 1100....but i installed myself

silverbeast

iTrader: (16)

damn, i hope my wife never reads this thread . she told me i could put a cam in but if she reads this she will pass out!! i will definitely be looking for a package deal.

apexman

275 new MTI T1
200 918 valve springs
260 used Mac headers and Y pipe
70 MSD wires
65 NGK TR55 plugs
500 LS1edit dyno tune
labor free I did all the work

1370 and alot more power!

AustinL911

iTrader: (-1)

TReX package-850
pacesetter race headers-405
O2 extentions-50
O2 sims-90
hypertech 160* Tstat-50
Ported LS6 oil pump-130
new headbolts-60
new headgaskets-30
Rollmaster timing set-100
+Some other stuff I can't remember from TSP....

(Items I still need to purchase)
aluminum flywheel, used-225
spec stage 3 clutch-~400
rearend-~2400
Laptop~800
HP Tuners~510
LM-1 or other wideband~3-500
another set of headbolts-60
another, better set of headgaskets-40-60
heads-1600-2300
another set of stock valves(temporary)-40
TSP rumbler true dual dumped exhaust-410
install-0, I did it

total to get my car through phase 1- $8585....

ok....I'm gonna go cry now....