Got my FMS Baby Solid Roller
10-06-2004, 06:26 AM
#1
TECH Fanatic
Thread Starter
iTrader: (9)
Join Date: Jan 2002
Location: DFW
Posts: 1,245
Likes: 0
Received 0 Likes
on
0 Posts
Got my FMS Baby Solid Roller Got my FMS Custom Grind Solid Roller in, I know its kinda small but I think it will work 
Here is the Cam Card
If you have trouble seeing the card it is a 275.7/290 732/731 114+4
Here is the Cam Card
If you have trouble seeing the card it is a 275.7/290 732/731 114+4
10-06-2004, 06:36 AM
#2
TECH Senior Member
iTrader: (1)
Join Date: Nov 2001
Location: Waco, TX
Posts: 6,449
Likes: 0
Received 0 Likes
on
0 Posts
Nice... but I heard that Cam Motion ground all the ones with the copper colored center sections wrong. You might want to double check...
(j/k)
What lifters are you going to be running?
(j/k)
What lifters are you going to be running?
10-06-2004, 06:40 AM
#3
TECH Fanatic
Thread Starter
iTrader: (9)
Join Date: Jan 2002
Location: DFW
Posts: 1,245
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Camaroholic
Nice... but I heard that Cam Motion ground all the ones with the copper colored center sections wrong. You might want to double check...
(j/k)
What lifters are you going to be running?
(j/k)
What lifters are you going to be running?
I am going to run Morel's 
Trending Topics
10-06-2004, 10:53 AM
#9
TECH Addict
iTrader: (15)
Join Date: Sep 2002
Location: Gainesville, GA
Posts: 2,538
Likes: 0
Received 0 Likes
on
0 Posts
I hope you don't have as many issues with that cam as I did with mine. Sheesh. Finally got the bugs worked out though. Hint: measure your cranking compression before you install the motor in the car.
10-06-2004, 12:04 PM
#10
TECH Fanatic
Thread Starter
iTrader: (9)
Join Date: Jan 2002
Location: DFW
Posts: 1,245
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by LOnSLO
I hope you don't have as many issues with that cam as I did with mine. Sheesh. Finally got the bugs worked out though. Hint: measure your cranking compression before you install the motor in the car.
10-06-2004, 01:24 PM
#11
TECH Addict
iTrader: (15)
Join Date: Sep 2002
Location: Gainesville, GA
Posts: 2,538
Likes: 0
Received 0 Likes
on
0 Posts
I had a lot of P/V issues obviuosly that took forever to fix. I didn't have time to put it on the engine dyno, so I just slapped the motor in the car. I degreed it in on a 109 ICL, but lost too much cylinder pressure. Took it down to a 104 and all is well. Numbers tomorrow finally. Still made 525rwhp like I had it before, but only 420 ft/lbs 
Note: you have a little less overlap than me, but that's one thing to check.
Note: you have a little less overlap than me, but that's one thing to check.
10-07-2004, 12:01 AM
#13
Originally Posted by BTL FED
Got my FMS Custom Grind Solid Roller in, I know its kinda small but I think it will work
If you have trouble seeing the card it is a 275.7/290 732/731 114+4
If you have trouble seeing the card it is a 275.7/290 732/731 114+4
Shud up Andrew..
10-07-2004, 05:34 AM
#15
TECH Fanatic
Thread Starter
iTrader: (9)
Join Date: Jan 2002
Location: DFW
Posts: 1,245
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by KingCrapBox
Lookin' awesome!
Originally Posted by Futral Motorsports
Just viewed your progress page,really nice! Cool gauges,that thing should really fly!
Shud up Andrew..
Shud up Andrew..
Last edited by BTL FED; 10-07-2004 at 06:41 AM.
