427ci LS2 Sleeved, 4 barrel TB, port FI, NA, dry sump, engine build.
#1
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
427ci LS2 Sleeved, 4 barrel TB, port FI, NA, dry sump, engine build.
I am in the process of building a new engine for my Camaro. I want to build an engine that will run on the street for cruising, hold up for 25 min runs on road courses (track day events), and take the abuse of occasional ¼ mile drag racing with my friends. In the past I have always run gen 1 small blocks, but this time I want to do an LS engine. This will be a fresh start and I want to explore the potential of the gen IV engines I’ve read so much about. My goal is to build an engine that runs strong off the bottom, builds power up to 7,000 RPM, puts out 650HP at the crank, runs on 92 octane pump gas, and takes some abuse!
Here is what I have so far:
LS2 sleeved block, 427 CID, 4.125” bore x 4.0” stroke
Manley forged crank and Manley H-beam rods
Weisco forged pistons, compression ratio ~11.5:1
LS7 CNC ported heads with titanium intake valves
T&D shaft rocker system
247/255 @ 0.050 Cam, 112 LSA
NRC dry sump oil system with 4 stage oil pump
Kooks 1-7/8” headers, 3” exhaust into 3” X-pipe reduced to 2-1/2” tail pipes
Katech Aluminum flywheel with modified ZR1 Corvette twin disc clutch (20% more clamp force)
Vaporworx fuel system with standalone digital controller, and GM CTS-V fuel pump (380lph capacity)
GM ECM and GM card style MAF sensor
Custom wiring harness
FAST 4150 throttle body
Custom built cold air intake
At this point I have gathered all of the parts listed above and the engine is in the final assembly stage. My goal is to have the engine tested and tuned on the engine dyno within the next two weeks, and then installed in my car by mid June. I plan to post updates, and pictures as I go along. Questions or comments on this build are always welcome. I have always picked up good information here, now I thought it would be a good time to share my project. This is the first forum I have posted on so bear with me.
Here is what I have so far:
LS2 sleeved block, 427 CID, 4.125” bore x 4.0” stroke
Manley forged crank and Manley H-beam rods
Weisco forged pistons, compression ratio ~11.5:1
LS7 CNC ported heads with titanium intake valves
T&D shaft rocker system
247/255 @ 0.050 Cam, 112 LSA
NRC dry sump oil system with 4 stage oil pump
Kooks 1-7/8” headers, 3” exhaust into 3” X-pipe reduced to 2-1/2” tail pipes
Katech Aluminum flywheel with modified ZR1 Corvette twin disc clutch (20% more clamp force)
Vaporworx fuel system with standalone digital controller, and GM CTS-V fuel pump (380lph capacity)
GM ECM and GM card style MAF sensor
Custom wiring harness
FAST 4150 throttle body
Custom built cold air intake
At this point I have gathered all of the parts listed above and the engine is in the final assembly stage. My goal is to have the engine tested and tuned on the engine dyno within the next two weeks, and then installed in my car by mid June. I plan to post updates, and pictures as I go along. Questions or comments on this build are always welcome. I have always picked up good information here, now I thought it would be a good time to share my project. This is the first forum I have posted on so bear with me.
Last edited by DaleTx; 01-10-2013 at 06:35 PM.
#2
I did something very similar, and it should be a great engine! Your cam choice looks interesting. You went higher on the duration, lower on the lift than I did.
What year Camaro? How did you hear about Vaporworx? Do you know Carl? He's running One Lap as we speak...
What year Camaro? How did you hear about Vaporworx? Do you know Carl? He's running One Lap as we speak...
#3
ModSquad
iTrader: (6)
Nice job! What accessory drive brackets are those? Im looking for something like that. Simple and sweet. I've ran the KRC stuff previously, without any problems. I know Ken personally. Great guy.
#4
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
The engine builder selected the cam for this build. Can't wait to see how it runs.
The engine will be going in my 1969 Camaro.
#5
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
The alternator bracket and power steering pump bracket were made by nutter racing engines. They manufacture lots of parts for LS engines. I purchased the accessory brackets and the dry sump 4 stage pump kit from them. Good stuff. email: ac@nutterracingengines.com
#6
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
I am hoping that with the right cam; tune, and air intake setup I can get good results with the single plane 4-barrel TB setup. I know I’m going to give up some mid-range power but should gain HP on the top end. I have some extra room under the hood so I thought I would explore the potential of this set up just to try something different.
I have built a couple of different cold air intakes to duct air into the 4-barrel throttle body for testing on the dyno. One setup is an extreme velocity pro series elbow into 4” O.D. tubing with a GM card style MAF sensor; then 5” O.D. tubing connected to a cone style air filter. The second setup is a complete custom air intake made with some purchased parts and some homemade parts; then 4” O.D. tubing with a GM card style MAF sensor; then 5” O.D. tubing connected to a cone style air filter. The second setup will have a lower profile than the first.
The goal is to achieve smooth air flow over the MAF sensor and smooth air flow into the 4-barrel TB. Also, I have the option to do a cowel induction air intake set-up with this engine but this would not allow use of the MAF sensor. This setup would require a speed density tune. I would rather see if we can make the MAF tune work. Lots of options, we’ll see.
If anyone has experience with this type of setup, or any comments or ideas about this build I’m open for discussion, thanks.
I have built a couple of different cold air intakes to duct air into the 4-barrel throttle body for testing on the dyno. One setup is an extreme velocity pro series elbow into 4” O.D. tubing with a GM card style MAF sensor; then 5” O.D. tubing connected to a cone style air filter. The second setup is a complete custom air intake made with some purchased parts and some homemade parts; then 4” O.D. tubing with a GM card style MAF sensor; then 5” O.D. tubing connected to a cone style air filter. The second setup will have a lower profile than the first.
The goal is to achieve smooth air flow over the MAF sensor and smooth air flow into the 4-barrel TB. Also, I have the option to do a cowel induction air intake set-up with this engine but this would not allow use of the MAF sensor. This setup would require a speed density tune. I would rather see if we can make the MAF tune work. Lots of options, we’ll see.
If anyone has experience with this type of setup, or any comments or ideas about this build I’m open for discussion, thanks.
Last edited by DaleTx; 01-10-2013 at 06:38 PM.
Trending Topics
#8
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
#9
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
On this build I decided to go with a 4.125" bore x 4.0" stroke sleeved LS2 block. Below is a shot of the underside of the block with the sleeves installed, and a shot with the pistons installed.
The 4.125" bore allowed the use of the LS7 heads. Originally I was going to use hand ported L92 heads with stainless valves..... but ended up doing the LS7 heads (that snowball thing!). When I went to the LS7 head I opted for the titanium valves since this is what they were originally designed to run.
Also... we are running bee-hive springs. comments? good results, bad results?
I am really curious to find out how the LS7 cnc ported heads run. The engine builder did a similar engine (427ci LS3 hand ported heads with an LS intake and similar cam) and made 630HP, can't remember the torque number.
The 4.125" bore allowed the use of the LS7 heads. Originally I was going to use hand ported L92 heads with stainless valves..... but ended up doing the LS7 heads (that snowball thing!). When I went to the LS7 head I opted for the titanium valves since this is what they were originally designed to run.
Also... we are running bee-hive springs. comments? good results, bad results?
I am really curious to find out how the LS7 cnc ported heads run. The engine builder did a similar engine (427ci LS3 hand ported heads with an LS intake and similar cam) and made 630HP, can't remember the torque number.
Last edited by DaleTx; 01-10-2013 at 06:39 PM. Reason: picture spacing
#10
TECH Addict
iTrader: (1)
I can't tell what your last CAI picture is of, but it reminds me of an idea I'd really like to see; filterless 14" snorkel style air cleaner with the snorkel ingegrating a card MAF and connecting to a 4" duct out to a hidden cone filter under the fender. It would have a completely retro look to it while incorporating EFI. Internally I would use an elbow like your carb hat elbow so there isn't a tone of volume added inside the 14" diameter. May not really fit with your build, but I just like the idea.
#11
ModSquad
iTrader: (6)
Thanks for the link. Email is sent.
#12
Glad to hear you had good results with a similar setup! I found out about the Ricks tanks and the vaporworx setup when I went to the SEMA show a couple of years ago. I called Carl last year and he was great to work with. I ended up getting the CTS-V fuel pump with 380lph output. Carl recommended this pump when you get over 600HP. Nice setup. We will be testing the vaporworx digital controller and CTS-V fuel pump when we run the engine on the dyno.
The engine builder selected the cam for this build. Can't wait to see how it runs.
The engine will be going in my 1969 Camaro.
The engine builder selected the cam for this build. Can't wait to see how it runs.
The engine will be going in my 1969 Camaro.
Here's my motor:
https://ls1tech.com/forums/generatio...ls7-build.html
And my 69:
You should head over to Lateral-G.net and Pro-touring.com! You'll be right at home there
#13
TECH Junkie
iTrader: (11)
Here's a graph of my "paper tiger" engine as I am planning it out. So far, it's a 4.07 x 4.10 L-92 motor with Patriot 2.08" valve cathedral port heads, a Victor, JR intake with 40# injectors and a 1200 CFM throttle body. Cam is a small off-the-shelf Comp solid roller with 235°/240° and 0.646"/0.641" on a 113°. Mine intentionally peaks at 6,000, so it would appear that there is more to be had in your combo, at least on paper...
#14
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
I can't tell what your last CAI picture is of, but it reminds me of an idea I'd really like to see; filterless 14" snorkel style air cleaner with the snorkel ingegrating a card MAF and connecting to a 4" duct out to a hidden cone filter under the fender. It would have a completely retro look to it while incorporating EFI. Internally I would use an elbow like your carb hat elbow so there isn't a tone of volume added inside the 14" diameter. May not really fit with your build, but I just like the idea.
I plan to test the extreme velocity pro series elbow and the air cleaner style set up when we test the engine on the dyno. I will plumb a vacuum gauge into the 4" O.D. tubing to compare the two set ups at various RPM's. I'm not sold on the elbow set up yet. Not sure how well a 90 degree elbow works on a NA set up (with no head of pressure like on a boost set up). I want to minimize restriction of air flow and turbulence as much as possible. Anyway it will be worth a try to see how each set up works with the MAF tune.
This picture should show the inside of the chamber better.
Last edited by DaleTx; 01-10-2013 at 06:40 PM. Reason: picture spacing
#15
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
Nice car! I went w the CTS-V set up and digital controller as well. Not cheap, but you will have no fuel starvation issues at all.
Here's my motor:
https://ls1tech.com/forums/generatio...ls7-build.html
And my 69:
You should head over to Lateral-G.net and Pro-touring.com! You'll be right at home there
Here's my motor:
https://ls1tech.com/forums/generatio...ls7-build.html
And my 69:
You should head over to Lateral-G.net and Pro-touring.com! You'll be right at home there
#16
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
Here's a graph of my "paper tiger" engine as I am planning it out. So far, it's a 4.07 x 4.10 L-92 motor with Patriot 2.08" valve cathedral port heads, a Victor, JR intake with 40# injectors and a 1200 CFM throttle body. Cam is a small off-the-shelf Comp solid roller with 235°/240° and 0.646"/0.641" on a 113°. Mine intentionally peaks at 6,000, so it would appear that there is more to be had in your combo, at least on paper...
#17
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
The engine was installed and run on the dyno today...
Results of day one tuning:
Peak Torque: 571 @ 5,400 RPM
Peak Hp: 670 @ 7,000 RPM
The horsepower curve was very smooth... we ran up to 7,300 RPM and the power was just starting to taper off. Torque was at 508 lb-ft at 3,500 rpm.
Very happy with the results so far. The engine was run with a speed density tune and pump gas (92 octane). We tested the CTS-V fuel pump and vaporworx digital controller at the same time. The pump maintained a solid 58 psi through out the run.
The CNC ported LS7 heads are very good. I will post up graphs and video over the next couple of days.
Cheers!
Results of day one tuning:
Peak Torque: 571 @ 5,400 RPM
Peak Hp: 670 @ 7,000 RPM
The horsepower curve was very smooth... we ran up to 7,300 RPM and the power was just starting to taper off. Torque was at 508 lb-ft at 3,500 rpm.
Very happy with the results so far. The engine was run with a speed density tune and pump gas (92 octane). We tested the CTS-V fuel pump and vaporworx digital controller at the same time. The pump maintained a solid 58 psi through out the run.
The CNC ported LS7 heads are very good. I will post up graphs and video over the next couple of days.
Cheers!
Last edited by DaleTx; 01-10-2013 at 06:42 PM.
#19
Staging Lane
Thread Starter
Join Date: Apr 2012
Location: Pacific NW
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
The engine was installed and run on the dyno today...
Results of day one tuning:
Peak Torque: 571 @ 5,400 RPM
Peak Hp: 670 @ 7,000 RPM
The horsepower curve was very smooth... we ran up to 7,300 RPM and the power was just starting to taper off. Torque was at 508 lb-ft at 3,500 rpm.
Very happy with the results so far. The engine was run with a speed density tune and pump gas (92 octane). We tested the CTS-V fuel pump and vaporworx digital controller at the same time. The pump maintained a solid 58 psi through out the run.
The CNC ported LS7 heads are very good. I will post up graphs and video over the next couple of days.
Cheers!
Results of day one tuning:
Peak Torque: 571 @ 5,400 RPM
Peak Hp: 670 @ 7,000 RPM
The horsepower curve was very smooth... we ran up to 7,300 RPM and the power was just starting to taper off. Torque was at 508 lb-ft at 3,500 rpm.
Very happy with the results so far. The engine was run with a speed density tune and pump gas (92 octane). We tested the CTS-V fuel pump and vaporworx digital controller at the same time. The pump maintained a solid 58 psi through out the run.
The CNC ported LS7 heads are very good. I will post up graphs and video over the next couple of days.
Cheers!
I will inquire to see if we can run the 1-7/8" Kooks while the engine is on the dyno. My headers may be to narrow to fit though.
Last edited by DaleTx; 01-10-2013 at 06:44 PM.
#20
ModSquad
iTrader: (6)
Congrats on those numbers! Wow! You will pick up a little with 1 7/8 headers. That thing wants to breathe. Nice job!