ms4 all the way
#2
i've never heard this exact setup, but in the past when you pair a large cam (such as your ms4) with loudmouth or loudmouth 2, you get a very "crackly" sound similar to many high performance drag cars. If you like that sound, a cam like that would be good.
#3
TECH Enthusiast
iTrader: (23)
Join Date: Mar 2004
Location: North Olmsted, OH
Posts: 673
Likes: 0
Received 0 Likes
on
0 Posts
How far are you planning to spin the engine? Wouldn't a 114 on that particular cam put the peak Hp around 7k may be even a bit higher?
I just got done installing one in my car with the standard 111 lsa. Here are my comments so far. My car is going to be a bit limited due to my stock manifolds however I have ORY and a Borlamouth (XR-1 mufler). Without a tune it was vicious the car would not hold idle to save it's life, it was almost undrivable. It would die, surge and buck. After I tuned the idle, so called "misfires", spark tables and error codes, the car drove pretty good for such a big cam. As far as sounds it rattles the walls in the garage. It does make the car sound like there is bigblock stuffed under the hood. I drove it to work for 2 days so far and have gotten nods and thumbs up. Once you step un it it pulls hard all the way to redline. I dropped it off tonite to get dynotuned so we will see how it does as far as hp. God willing headers and TSP Stg 1 heads are in its future, but I'm going to enjoy it as is until it goes for it's winter slumber.
I'll post a video as soon as I get a chance.
I just got done installing one in my car with the standard 111 lsa. Here are my comments so far. My car is going to be a bit limited due to my stock manifolds however I have ORY and a Borlamouth (XR-1 mufler). Without a tune it was vicious the car would not hold idle to save it's life, it was almost undrivable. It would die, surge and buck. After I tuned the idle, so called "misfires", spark tables and error codes, the car drove pretty good for such a big cam. As far as sounds it rattles the walls in the garage. It does make the car sound like there is bigblock stuffed under the hood. I drove it to work for 2 days so far and have gotten nods and thumbs up. Once you step un it it pulls hard all the way to redline. I dropped it off tonite to get dynotuned so we will see how it does as far as hp. God willing headers and TSP Stg 1 heads are in its future, but I'm going to enjoy it as is until it goes for it's winter slumber.
I'll post a video as soon as I get a chance.
#5
TECH Addict
Join Date: Jul 2002
Location: Somewhere I Belong
Posts: 2,906
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 99WS7
Damn...I just cant decide. Most are enjoying this cam a lot. I want to see what kind of numbers it will make with decent heads and full bolt ons.
peace
#6
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Jan 2006
Posts: 1,782
Likes: 0
Received 0 Likes
on
0 Posts
well i wqas planniing on going with the set up in my sig but i was going to keep my stock exhaust b/c the cops around here are real a$$holes and when i was going to run i would just open my cut outs. i am planning to spin it around about 6800
#7
TECH Enthusiast
iTrader: (46)
Join Date: Dec 2005
Location: Atlanta, GA
Posts: 525
Likes: 0
Received 0 Likes
on
0 Posts
I just ordered the MS4 with the PRC LS6 Stg 1 heads with CNC job. Got catless LTs and Spintech Side exhaust. As of right now TSP has the MS4 backordered for a week. I will post video when I get it done and eventually a dyno. Its going on a 2004 GTO (if you havent noticed).
Trending Topics
#8
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Jan 2006
Posts: 1,782
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Oh4GTO
I just ordered the MS4 with the PRC LS6 Stg 1 heads with CNC job. Got catless LTs and Spintech Side exhaust. As of right now TSP has the MS4 backordered for a week. I will post video when I get it done and eventually a dyno. Its going on a 2004 GTO (if you havent noticed).
#9
TECH Enthusiast
iTrader: (46)
Join Date: Dec 2005
Location: Atlanta, GA
Posts: 525
Likes: 0
Received 0 Likes
on
0 Posts
Woohoo big 18. Im going with the 111 LSA for better torque down low. Last time I checked TSPs website tey only offer 111 or 112 LSA. Unless your going custom. Id do the 111 LSA for more torque. The only downfall of a tight LSA is worse gas mileage. Its not that bad but there. Maybee about .5 MPG less. But Im sure you didnt get this car for its economy. You should still do well since youve got LTs and porting everything on the intake side. The stock heads wont hold you back too much.
#10
LS1 Tech Administrator
iTrader: (14)
114LSA on that cam will give you horrible valve events for a 346. Dynamic compression will be in the toilet. 111LSA is good. 110LSA is even better.
__________________
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2018 Cadillac Escalade 6.2L A10 Pat G tuned.
LS1,LS2,LS3,LS7,LT1 Custom Camshaft Specialist For custom camshaft help press here.
Custom LSX tuning in person or via email press here.
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2018 Cadillac Escalade 6.2L A10 Pat G tuned.
LS1,LS2,LS3,LS7,LT1 Custom Camshaft Specialist For custom camshaft help press here.
Custom LSX tuning in person or via email press here.
#13
I thought the 111lsa would rev out higher then a 114? Thats what Combination told me about my LT1. Unless the mechanics are different on LS1s.
I myself am looking for a cam that will make great power... except I want to keep my redline much like stock. Around 6k...
I myself am looking for a cam that will make great power... except I want to keep my redline much like stock. Around 6k...
#15
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Jan 2006
Posts: 1,782
Likes: 0
Received 0 Likes
on
0 Posts
yeah i was thinking about it today and i t hink i am going to go with 110. i said screw it and might as well get everything outa this cam that i can. with 110 what would i spin it to and do you think that a 3600 converter would be too big for this cam?? and im going with yank and nothing else
#16
TECH Fanatic
iTrader: (1)
Join Date: Nov 2005
Location: Goldsboro, NC
Posts: 1,142
Likes: 0
Received 0 Likes
on
0 Posts
I got the MS4 on 111lsa. Idle is lopey as hell. Its really loud. My numbers are in sig. The sound by itself lost me 3 races. They wanted to, then they heard it and said nevermind. Intimidation rocks. My 111 peaked out at 6850ish. Stock pulley, throttle body and manifold. 433rwhp not too bad.
#19
Originally Posted by transamfreak01
yeah wouldnt i have to fly cut with a 110????
yes you would go to this thread and read post 88, if you are lazy here you go
'' We offer MS4 camshafts on a 110 , but for p/v issues it's only available to customers with cut pistons. '' Jason Texas-Speed
Originally Posted by cws T/A