Must sell 1000hp WS6 for bills fast.
03-10-2014, 07:17 PM
#1
Launching!
Thread Starter
iTrader: (55)
Join Date: Jan 2007
Location: Valley Center, CA
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
Must sell 1000hp WS6 for bills fast. Year: 2001
Make: Pontiac
Model: Trans Am
Price: $12000
Mileage: 50000
Private or Dealer Listing: Private Listing
Location (State): CA
Color: Blue
Transmission: Manual
Drivetrain: Rear Wheel Drive
LS Engine?: Car has LS engine
Navy blue metalic
403 iron block from rpm built for 1600hp
Pinned billet mains from Callie's
Callie's dragon slayer
Wiseco pistons pistons at 9.5:1 cr
Ackley and child's rings
Tool steel wrist pins Howard rods
Arp everything
1/2" head studs vs 11m
Melling oil pump
Morel race lifters good for 8k rpm
Edelbrock 245cc racing heads CNC'ed by west coast cylinder heads incolell steel exhaust valves. Jr victor intake with quad rail for alcohol or e85. New Boost cam speced by CMS. Brand new 2" primary headers full stainless.
T56 viper spec Trans fresh built
Tci sfi cert bell
Brand new never used moser 9"
44 splined axles, full spool, I think 3.55 gears. 5/8 wheel studs.
2 step, low impedance injector driver, timing redard for nitrous and window switch. Stand alone fuel cell for spray with regulators and feed for spray.
Wolf chromoly cage 6 point. Madman suspension, wheelie bar, lower control arms, tubular suave sink for race and street, two brake set ups, street bear brakes, drag aerospace brakes. Vfn race hood with full length risers. Bigs and skinnies. Brand new never used.
There is more stuff to like detach steering wheel, remote battery box and orther stuff. The only thing it needs is drive shaft and clutch. That was because I was going with a F2 Procharger and gear drive. Then I thought the F1R with an aster bracket would be the best and easiest set up and make 1100rwhp with E85. It's been sitting for about 3 years. Motor Trans and rear end are new.
Rims and tires are brand new too. Title in hand, it NOT a salvaged f-body. Lost my job. Trying to keep my home. Wife is prego with 2nd child.
Please call or txt 209-559-7342 8am-10pm Cali time.
Last edited by haighter; 03-10-2014 at 09:49 PM.
03-10-2014, 09:49 PM
#4
Launching!
Thread Starter
iTrader: (55)
Join Date: Jan 2007
Location: Valley Center, CA
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
I am on my cell phone. I am not sure how to post the pics on here that way.
I didnt get a txt from canada4g63. Please make sure to send it to 209-559-7342. Thank you. I have some older pics of it on photobucket. I can pull those off. Just nothing that is within the last few weeks.
I didnt get a txt from canada4g63. Please make sure to send it to 209-559-7342. Thank you. I have some older pics of it on photobucket. I can pull those off. Just nothing that is within the last few weeks.
03-10-2014, 10:02 PM
#5
Launching!
Thread Starter
iTrader: (55)
Join Date: Jan 2007
Location: Valley Center, CA
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
old video of old setup on 150shot and heads cam headers with tune
old parts
old 402 set up with 150 shot. made 560rwhp on pump 780hp on 150 shot
old parts
old 402 set up with 150 shot. made 560rwhp on pump 780hp on 150 shot
03-10-2014, 10:16 PM
#7
Launching!
Thread Starter
iTrader: (55)
Join Date: Jan 2007
Location: Valley Center, CA
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
No procharger. I had to sell it. It has everything to make it run but a drive shaft and clutch. Again no blower into cooler or any post parts on it anymore.
