!!! 
its looking good! 
it's gettin' close!
Thread Starter
Joined: Oct 2006
Posts: 2,608
Likes: 0
From: Webb City, MO...out in the garage
I'm pretty sure the street pump is 55gpm and the race pump is 35gpm if I remember. I did delete the AC but I kept the heat.
...oh by the way, I put the engine in tonight
...oh by the way, I put the engine in tonight
Thread Starter
Joined: Oct 2006
Posts: 2,608
Likes: 0
From: Webb City, MO...out in the garage
Only pics i have right now, i'll get some better ones later. I figured these were good enough for now
As for thing i have left to do, just in case you all are curious:
As for thing i have left to do, just in case you all are curious:
- Install fuel tank & run lines
- Install torque arm & weld brace - re-powdercoat
- smooth brake calipers a bit - powdercoat
- finish running electrical harnesses
- re-install brakes, fill & bleed
- re-install transmission, bleed hydraulics
- SELL MOTORCYCLE
- paint hood
- order water pump
- order intake
- order 100mm lid
- order driveshaft
- fab exhaust
- tune
- do a burnout
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
yay an update! this is by far my favorite build thread to check in on. the detail is just over the top- painting that front bumper support that no one will ever see is a fine example. can't wait to see this thing 100%
Thread Starter
Joined: Oct 2006
Posts: 2,608
Likes: 0
From: Webb City, MO...out in the garage
Thanks guys. I know its been really slow goin' but the economy has cut my paycheck in half and i really don't want to make any compromises. We're in the home stretch though.
The only thing that MIGHT hinder me right now is that a local Airgas salesman likes my bike and i like the Miller Dynasty 200 DX Tigrunner setup they accidentily delivered to my employer today. We might be working out a trade/partial trade with each other and depending on whether or not i can get the welder + cash, it could hold me back a bit on finishing the car. I can use the welder to make money of course, probably just on this site, but if i don't sell the bike outright i won't have much money to toss at the SS. If he wants to trade, it'll be a hard deal to pass up because the welder is priced at 5% over their cost. If i sell the bike outright, i won't buy the welder, but it's been too hard to sell it so far so if he wants to trade i'm doing it.
The only thing that MIGHT hinder me right now is that a local Airgas salesman likes my bike and i like the Miller Dynasty 200 DX Tigrunner setup they accidentily delivered to my employer today. We might be working out a trade/partial trade with each other and depending on whether or not i can get the welder + cash, it could hold me back a bit on finishing the car. I can use the welder to make money of course, probably just on this site, but if i don't sell the bike outright i won't have much money to toss at the SS. If he wants to trade, it'll be a hard deal to pass up because the welder is priced at 5% over their cost. If i sell the bike outright, i won't buy the welder, but it's been too hard to sell it so far so if he wants to trade i'm doing it.
Teching In
Joined: Apr 2006
Posts: 22
Likes: 0
From: Greeley Colorado
Really matt i have to say ur sig. is completly gay. 850hp on blower alone stop lieing to these people.. ur car has never dynoed over 300hp ya its getting built but u wont ever see those numbers sorry to bust ur *****.... Hail to the 850hp king hail hail
