hugger427

iTrader: (9)

Before wire mod and evap/heatercore removal:
http://community.webshots.com/photo/...28323993vDBryX
http://community.webshots.com/photo/...28324117KEbNWW

After wire mod and removal of evap/heatercore and relocation of battery:
http://community.webshots.com/photo/...28324294cwgBOe
http://community.webshots.com/photo/...28324570CFLErz
http://community.webshots.com/user/rh2772

much work yet to be done, like even out the coil relocation kit and hide the PCM wire looms, etc., etc., etc......but when is a project ever really finished

screamin chicken

looks nice and clean, i want to do the wire mod myself, but I just swapped the cam and installed headers and I dont want to work on it for awhile, it's crazy to do thing like that with out a lift (Headers) ......

Todd2001SS

You do not need to do anything, 427 says it all!

Steve1969LS1

iTrader: (1)

Very nice and clean.. now you just need to re-route (hide) those ground wires

Again, good work!

hugger427

iTrader: (9)

Steve, I want to thank you very much for taking the time and creating the "Wire Mod" thread...very helpful, very cool.

The more I clean the engine bay up the more things stick out like the ground wires and especially the PCM looms. Oh well...easy stuff to correct at this point.

Thanks again

quickWS6

Looks good, pull that power steering pump for an even cleaner look.

hugger427

iTrader: (9)

I'll give up air, I'll give up heat, I'll even go through the pains of a wire mod and battery relo for the greater good of looks and/or weight reduction but when it come to power steering ...that baby stays.

2 SLOW

How much will it cost for you to do mine??

Scott 00TA

I wish mine looked like that

RealDealCamSS

iTrader: (1)

Congratulations, you have the baddest SS vert I've ever seen. LOVIN' the Hugger/white combo.

The only other thing I like is when the convertibles have the "nice looking" roll bar.

MOBE

that looks great!

Kens_02SS

iTrader: (11)

Looks good, where did you get those ( i think) chrome looking caps when you did the wire mod!?

swandogg25

iTrader: (2)

Looks great! I had done the !wire mod last summer but I just got around to pulling the a.i.r. pump and e.g.r this past weekend. Looks so much better in there. Oh and re-route the hood release cable too!

hugger427

iTrader: (9)

thanks for the comments guys...
- swandogg25 - groud wire, hood release along with PCM loom are next...
- Kens_02SS - those are stainless bolts with lock tighted nuts.
- RealDealCamSS - no cage on my watch. It's just a drop top cruiser but thanks for the props.
- 2 SLOW -$9,999.99 today only!!!

Some day I'm gonna relocate pcm and fuse boxes under dash where the heater core was where ther is plenty o' room. Than I want to figure out a way to minimze the power steering pump by lowering out of site...than there's that master cylinder, hum that's gonna be tough. Basically, many winter projects a head for a car that never will be finished.

XtinctHawk02

That does look nice and clean. No clutter what so ever.
Good Job!

Derek98z

iTrader: (55)

Are you bringing it to RMS on Saturday? I'd like to check it out.

hugger427

iTrader: (9)

Hey Derek. I plan on going to the RMS event...have to fit it between soccer, wedding, and weather. I look forward to seeing you there...suppose to be around 150 cars

Nine Ball

iTrader: (38)

Damn that is one sweet SS.

Scalpel

iTrader: (4)

That looks really good.

Too bad one can't make a sleek A/C system that could be incorporated nicely in the car.

JackZ28

Good lawd that car is beautiful!!