08 ly6 in a 2000 Sonoma
#303
TECH Enthusiast
Thread Starter
iTrader: (6)
Join Date: Dec 2007
Location: Rittman, Ohio
Posts: 734
Likes: 0
Received 0 Likes
on
0 Posts
Back in town from the lsx dyno day. Didnt end up putting the truck on the rollers since I figured Id better not risk it being 3 hrs from home even though I gave a bunch of people my buddy knows rides and basically beat the crap out of it for 2 days. Think the guy most impressed was a kid my age that owns a '10 370z so I felt thats pretty impressive. Not sure how fast I managed to get up to since the awesome 100mph speedo but whatever ~6200rpms in 4th 1:1 gear with 3.73 gears and 26" is what I got to twice. Buddy picked up a GoPro so that was some incentive .
My axle shaft seal on the drivers side started leaking friday morning before I left. Noticed the rank gear oil smell then cloud of smoke when slowing down from high speeds so its leaking pretty good. Hopefully its just the seal thats only 6yrs old so Ill replace that and the passenger side one this week.
Grabbed this off my shelf so will try to get going on installing it after feeling the brakes at high speeds and theres just no doubt about it that the pedal takes more force now to slow down.
My axle shaft seal on the drivers side started leaking friday morning before I left. Noticed the rank gear oil smell then cloud of smoke when slowing down from high speeds so its leaking pretty good. Hopefully its just the seal thats only 6yrs old so Ill replace that and the passenger side one this week.
Grabbed this off my shelf so will try to get going on installing it after feeling the brakes at high speeds and theres just no doubt about it that the pedal takes more force now to slow down.
#304
TECH Enthusiast
Thread Starter
iTrader: (6)
Join Date: Dec 2007
Location: Rittman, Ohio
Posts: 734
Likes: 0
Received 0 Likes
on
0 Posts
Uh oh somethings missing! Couldnt see anything majorly wrong with the axle shaft seal but it was still seeping around it so in goes new ones.
Rotors are stuck on the shafts but still managed to pound out the wheel studs so I can put longer ones in. The 1.5" long ones just barely made it through the threads of the stock acorn nuts with the zq8 and drag wheels but looked like they were too short since those lugnuts are so long so Ill put in longer studs and pick up new lug nuts so they will be safe and look better at the track.
Rotors are stuck on the shafts but still managed to pound out the wheel studs so I can put longer ones in. The 1.5" long ones just barely made it through the threads of the stock acorn nuts with the zq8 and drag wheels but looked like they were too short since those lugnuts are so long so Ill put in longer studs and pick up new lug nuts so they will be safe and look better at the track.
#305
TECH Addict
iTrader: (9)
Rotors are stuck on the shafts but still managed to pound out the wheel studs so I can put longer ones in. The 1.5" long ones just barely made it through the threads of the stock acorn nuts with the zq8 and drag wheels but looked like they were too short since those lugnuts are so long so Ill put in longer studs and pick up new lug nuts so they will be safe and look better at the track.
#306
TECH Enthusiast
Thread Starter
iTrader: (6)
Join Date: Dec 2007
Location: Rittman, Ohio
Posts: 734
Likes: 0
Received 0 Likes
on
0 Posts
I have moser axle shafts and at the time of having them built I chose the 1.5" long studs so I picked up their 2.5" long ones, Both .505" knurled so I should be fine just to press the new ones in correct?
#307
TECH Enthusiast
Thread Starter
iTrader: (6)
Join Date: Dec 2007
Location: Rittman, Ohio
Posts: 734
Likes: 0
Received 0 Likes
on
0 Posts
Ran up to the dealer to see if they can get me a replacement sightglass for the hydroboost unit I picked up. It came from a 05 yukon so we checked that and other various trucks from 05-06 and all showed the same diagram where all they can get is a replacement accumulator and a few seals. The diagram doesnt even show the sightglass. So Im going to contact the ebay seller I bought it from a few months ago and see if i can exchange it and if not Im wondering if theres something to use to block where the sight glass was. Maybe something along the lines of these at the hardware store.
#309
TECH Addict
iTrader: (9)
Dont feel like posting pics of the slips tonight but the runs were along the lines of best 13.13@113.3 with a bogging 2.2 60ft and then I spun through 1st badly towards the end of the night ending up a worst of 13.7@114 2.60 and 14.8@111.6 2.7 60ft
Best 60 I got all night was 2.1 I would either launch at 2.5k and it would grab like a **** and bog down or I was launching at 3k+ and just spinning. Needed feather the clutch instead of just dropping it but I wanted to just get a baseline. I try more stuff next time I go there. Spent a lot of time discussing my engine swap since there arent many ls swaps around here yet. Only s10 with one there.
Best 60 I got all night was 2.1 I would either launch at 2.5k and it would grab like a **** and bog down or I was launching at 3k+ and just spinning. Needed feather the clutch instead of just dropping it but I wanted to just get a baseline. I try more stuff next time I go there. Spent a lot of time discussing my engine swap since there arent many ls swaps around here yet. Only s10 with one there.
If not, your cam is 13 degrees retarded from specs and would account for the low-end bog..
(I'm trying to use my older L92 phaser that I sacreficed by taking it all apart, to degree and check PV clearance on my L99 VVT2 cam. So there's a little math involve to rotate it back to about where it would be with the new L99 phaser that I'll use to actually run the motor)
#310
TECH Enthusiast
Thread Starter
iTrader: (6)
Join Date: Dec 2007
Location: Rittman, Ohio
Posts: 734
Likes: 0
Received 0 Likes
on
0 Posts
Hmm I didnt know this. When I ordered they hadnt built actual ly6 cams like they do now so I told them my engine was the 6.0 ly6 and what my intentions were so they recommended the vvt-2. As far as phasers comp makes 2 different limiters depending on what years they are. TSP asked me for the p/n on my phaser and sent me the correct limiter for it. They never mentioned anything about actual cam core differences.
#312
TECH Enthusiast
Thread Starter
iTrader: (6)
Join Date: Dec 2007
Location: Rittman, Ohio
Posts: 734
Likes: 0
Received 0 Likes
on
0 Posts
Grabbed these while I was at summit getting the plumbing supplies. Had my eyes on them since they came out.
Pressure lines are plumbed. I have to grab a brass tee to hook up the return then finish up some small stuff and its done. Tons more room now, Its so much cleaner looking!
Pressure lines are plumbed. I have to grab a brass tee to hook up the return then finish up some small stuff and its done. Tons more room now, Its so much cleaner looking!
#314
TECH Enthusiast
Thread Starter
iTrader: (6)
Join Date: Dec 2007
Location: Rittman, Ohio
Posts: 734
Likes: 0
Received 0 Likes
on
0 Posts
All done havent driven it yet since Ive been working 12s 7 days a week and cant be picky when I get a chance to sleep.
Before
After
#315
TECH Enthusiast
Thread Starter
iTrader: (6)
Join Date: Dec 2007
Location: Rittman, Ohio
Posts: 734
Likes: 0
Received 0 Likes
on
0 Posts
Small update one of the dmh cutouts quit working. I plugged in the harness going to the other one to make sure it wasnt the wiring and it still doesnt work and i had it unbolted to make sure its not just warped like the other one was when i first installed it by not tightening it symetrically even and it wouldnt open so i have to call dmh and send it in. Good thing i still have the manual plates to put back on.
#320
On The Tree
iTrader: (1)
Join Date: May 2010
Location: Summerville, SC
Posts: 142
Likes: 0
Received 0 Likes
on
0 Posts
FYI. Get a linelock now that you have hydroboost. After we installed linelock on the 01 blazer I could hardly do a burnout. The higher the rpms the more the brakes wanted to clamp (4 wheel disc brakes)
Had my wife video the rear and you could see the calipers starting to glow. Just a heads up. You can hear it bog the motor down in this video.
Had my wife video the rear and you could see the calipers starting to glow. Just a heads up. You can hear it bog the motor down in this video.
Last edited by 00rcsb; 06-22-2012 at 10:40 AM.