Ls2 rx8
#1
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2014
Location: Detroit
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
D1SC Procharged LS2 RX8 Ronin 8.8 Rear End
Hey guys. I'm building an lsx swap RX8.
I used to build sportbikes for fun, as I'm only 20 and funds have never been sufficient for a car build.
Well, I decided to change that.
I picked up an 04 RX8 with blown Apex Seals in PA for 1500$
Brought her back to the mitten and stripped her down.
Later that week I found an 09 TBSS LS2 for 1600$ that looks brand new.
Found a T56 from an 01 Camaro SS with 70k for 800$
I purchased the LSX conversion kit from Stephen Villavaso (3500$)
LS1 water pump (140$)
LS1 Tensioner Pulley
LS1 Alternator (160$)
LS1 Balancer (65$)
LS2 Timing cover (85$)
LS1 Alt Bracket (75$)
T56 Bellhousing
T56 Rebuild kit
Trans lube (650$)
LS6 intake/injectors/fuel rail & 85mm TB purchased (570$)
Oil pan kit (85$)
Pro 5.0 Short Shifter (140$)
Will post pictures later. At SOS now.
I need help on my wire harness options. I can swap my DBC harness and use DBW since I have the 58x reluctor wheel or get the lingenfelter converter box and keep DBC. I'm pinching pennies now.. So I'm all ears for suggestions.
I used to build sportbikes for fun, as I'm only 20 and funds have never been sufficient for a car build.
Well, I decided to change that.
I picked up an 04 RX8 with blown Apex Seals in PA for 1500$
Brought her back to the mitten and stripped her down.
Later that week I found an 09 TBSS LS2 for 1600$ that looks brand new.
Found a T56 from an 01 Camaro SS with 70k for 800$
I purchased the LSX conversion kit from Stephen Villavaso (3500$)
LS1 water pump (140$)
LS1 Tensioner Pulley
LS1 Alternator (160$)
LS1 Balancer (65$)
LS2 Timing cover (85$)
LS1 Alt Bracket (75$)
T56 Bellhousing
T56 Rebuild kit
Trans lube (650$)
LS6 intake/injectors/fuel rail & 85mm TB purchased (570$)
Oil pan kit (85$)
Pro 5.0 Short Shifter (140$)
Will post pictures later. At SOS now.
I need help on my wire harness options. I can swap my DBC harness and use DBW since I have the 58x reluctor wheel or get the lingenfelter converter box and keep DBC. I'm pinching pennies now.. So I'm all ears for suggestions.
Last edited by Coda634; 04-04-2016 at 03:07 PM.
#2
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2014
Location: Detroit
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Purchased an e40 ECM and harness with DBW TB and Pedal along with a Lingenfelter converter box.
Now I just need some gaskets, a TOB Tube for the trans, a clutch, and a custom exhaust.
Build progress will start more this week.
Thanks to everyone on the forums offering the knowledge and awesome used parts to help complete this build!
Now I just need some gaskets, a TOB Tube for the trans, a clutch, and a custom exhaust.
Build progress will start more this week.
Thanks to everyone on the forums offering the knowledge and awesome used parts to help complete this build!
#4
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2014
Location: Detroit
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Thanks man, so far my tab looks like this..
RX8 - 1500$ 2500$ spent on trip
LS2 - 1600$ 1750$ spent on trip
Deluxe Kit - 3500$
LS6 intake/85mm TB/Rail/inj - 570$
E40 Harness - 225$
Lingenfelter TRG002 - 150$
Alternator - 140$
Water pump - 125$
Tensioner pulley - 15$
Belt - 15$
Alternator bracket - 80$
Oil pan - 160$
Oil pan kit - 85$
T56 - 800$ 1000$ spent on trip
T56 5.0 Shifter - 140$
T56 Rebuild - 400$
T56 Bellhousing - 250$
T56 Mainshaft - 250$
LS7 Clutch & Flywheel 445$
OEM Slave Cylinder - 50$
Fender Liners - 200$
F. Bumper impact absorber - 60$
R. bumper reinforcement - 50$
Mazda Speed Body Kit - 550$
Gaskets - 95$
11,455$ on car build
12,805$ + traveling costs
Just waiting on parts to arrive now
RX8 - 1500$ 2500$ spent on trip
LS2 - 1600$ 1750$ spent on trip
Deluxe Kit - 3500$
LS6 intake/85mm TB/Rail/inj - 570$
E40 Harness - 225$
Lingenfelter TRG002 - 150$
Alternator - 140$
Water pump - 125$
Tensioner pulley - 15$
Belt - 15$
Alternator bracket - 80$
Oil pan - 160$
Oil pan kit - 85$
T56 - 800$ 1000$ spent on trip
T56 5.0 Shifter - 140$
T56 Rebuild - 400$
T56 Bellhousing - 250$
T56 Mainshaft - 250$
LS7 Clutch & Flywheel 445$
OEM Slave Cylinder - 50$
Fender Liners - 200$
F. Bumper impact absorber - 60$
R. bumper reinforcement - 50$
Mazda Speed Body Kit - 550$
Gaskets - 95$
11,455$ on car build
12,805$ + traveling costs
Just waiting on parts to arrive now
Trending Topics
#8
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2014
Location: Detroit
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
I've been nickle and diming every bit where I could.
DELUXE KIT
Includes everything needed for the swap to save both time & money
Power-Train
• Engine Stands & LSX Adaptors & Rubber Engine Mounts
• Transmission Crossmember With Torque Arm
• Polyurethane Transmission Mount
• Custom Steel DriveShaft
• Aluminum CNC Machined Trigger Wheel
(Engine speed for instrument cluster)
Exhaust
• Exhaust Manifolds
Acceleration
• Throttle Cable
(I used a 2 Gen Rx7 throttle pedal. Will also
come with install hardware for the Rx7 pedal. Just
let me know your plans for this part)
Fuel Delivery
• In-Tank High Volume Fuel Pump
• Filter/regulator• Custom quick Disconnect Fuel lines
(This is for a returnless fuel rail. Contact me if otherwise)
Hydraulics
• Clutch Line
(For stock F-body Slave Cylinder)
• 7/8 Bore Clutch Master Cylinder
(The clutch is about the same as the stock feel of the Rx8)
Suspension
• Rack and Pinion Relocation Bracket
• Sway Bar Spacers
• Strut Bar Spacers
• Bump Steer Kit
(To correct the geometry of lowering
the rack for oil pan clearance)
Induction
• Crome Air Intake With Washable AirFilter
Battery
• Battery Relocation Cables
MISC
• Shifter Cover
• Shifter Relocation
Stephen himself answers questions regularly for me and that alone has been worth purchasing one of his kits. Very nice guy.
#9
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2014
Location: Detroit
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Updated pricing
RX8 - 1500$ 2500$ spent on trip
LS2 - 1600$ 1750$ spent on trip
Deluxe Kit - 3500$
LS6 intake/85mm TB/Rail/inj - 570$
LS1/411PCM&Harness - 350$
Lingenfelter TRG002 - 150$
Alternator - 140$
Water pump - 125$
Tensioner pulley - 15$
Belt - 15$
Alternator bracket - 80$
Oil pan - 160$
Oil pan kit - 85$
T56 - 800$ 1000$ spent on trip
T56 5.0 Shifter - 140$
T56 Rebuild - 400$
T56 Bearing Shims Snaprings -190$
T56 Bellhousing - 250$
T56 Mainshaft - 250$
LS7 Clutch & Flywheel 445$
OEM Slave Cylinder - 50$
Fender Liners - 200$
F. Bumper impact absorber - 60$
R. bumper reinforcement - 50$
Mazda Speed Body Kit - 550$
Gaskets - 95$
Bolts - 50$
11,720$ on car build
13,270$ + traveling costs
Sold old pcm & harness since pedal wouldn't fit for a 411pcn & harness (350$)
Sold harness for 225
(+125 overall)
Bolts + 50$
Needed bearings, races & snap rings for the t56 (+190$)
Oil pan came in today, cleaned it up.
Doing body work while waiting on engine parts. Now doing trans rebuild also.
Conversion & body kit should arrive over the weekend progress pics will reoccur soon.
RX8 - 1500$ 2500$ spent on trip
LS2 - 1600$ 1750$ spent on trip
Deluxe Kit - 3500$
LS6 intake/85mm TB/Rail/inj - 570$
LS1/411PCM&Harness - 350$
Lingenfelter TRG002 - 150$
Alternator - 140$
Water pump - 125$
Tensioner pulley - 15$
Belt - 15$
Alternator bracket - 80$
Oil pan - 160$
Oil pan kit - 85$
T56 - 800$ 1000$ spent on trip
T56 5.0 Shifter - 140$
T56 Rebuild - 400$
T56 Bearing Shims Snaprings -190$
T56 Bellhousing - 250$
T56 Mainshaft - 250$
LS7 Clutch & Flywheel 445$
OEM Slave Cylinder - 50$
Fender Liners - 200$
F. Bumper impact absorber - 60$
R. bumper reinforcement - 50$
Mazda Speed Body Kit - 550$
Gaskets - 95$
Bolts - 50$
11,720$ on car build
13,270$ + traveling costs
Sold old pcm & harness since pedal wouldn't fit for a 411pcn & harness (350$)
Sold harness for 225
(+125 overall)
Bolts + 50$
Needed bearings, races & snap rings for the t56 (+190$)
Oil pan came in today, cleaned it up.
Doing body work while waiting on engine parts. Now doing trans rebuild also.
Conversion & body kit should arrive over the weekend progress pics will reoccur soon.
#13
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2014
Location: Detroit
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Just ordered Hinson/Stainlessworks Long Tube Headers (1 7/8ths" inlets with 3" outlets)
Hinson/Stainlessworks Y-Pipe
(3" outlet)
For 1150$ shipped.
New the headers are 935 + shipping
New the Y-pipe is 435 + shipping.
These connect into the stock or aftermarket Mazda muffler.
I will be using a 3.5" aftermarket muffler.
Hinson/Stainlessworks Y-Pipe
(3" outlet)
For 1150$ shipped.
New the headers are 935 + shipping
New the Y-pipe is 435 + shipping.
These connect into the stock or aftermarket Mazda muffler.
I will be using a 3.5" aftermarket muffler.
#16
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2014
Location: Detroit
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
The travel cost is including what was spent on the car. Uhaul is expensive.
No updates yet, its below freezing in Michigan and I don't have a heated garage. Mom's fiance bailed and took all the tools, will be having it sent to a friends shop and finishing the work there.
I wish I could afford a C6, but I'm under 15k total invested. Can't find a C6 under 30k.
No updates yet, its below freezing in Michigan and I don't have a heated garage. Mom's fiance bailed and took all the tools, will be having it sent to a friends shop and finishing the work there.
I wish I could afford a C6, but I'm under 15k total invested. Can't find a C6 under 30k.
#18
I'm an RX fan but good lord the 8 is slower than dirt and responds very little to bolt-ons. Awesome project but that mount/conversion kit is crazy expensive. Looking forward to seeing the end product.
#20
Staging Lane
Thread Starter
iTrader: (1)
Join Date: Jul 2014
Location: Detroit
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Forgot I had a thread on here, been posting progress on no rotor.
Bent lip around engine bay for clearance
Dropped steering rack and sway bar so its ready for relocation once lip bending is finished
Stainless works long tubes and Y pipe
Test fit
Test fit is a success, & headers only fit if we took off the K member then reinstalled it.
Bent lip around engine bay for clearance
Dropped steering rack and sway bar so its ready for relocation once lip bending is finished
Stainless works long tubes and Y pipe
Test fit
Test fit is a success, & headers only fit if we took off the K member then reinstalled it.