'00 GT 6.0 swap
Thread Starter
Launching!
iTrader: (11)
Joined: Sep 2007
Posts: 247
Likes: 0
From: Hillsdale, Michigan
'00 GT 6.0 swap Here are a few pics of my ongoing '00 Mustang GT/LQ4 swap that I have been slowly working on the last couple of months.
I picked up a car with an engine noise for cheap and am throwing together an LQ4 (also picked up cheap!)
For the swap I went with an AJE k-member/mounts, UPR a-arms and coilovers. The car is going to be a cam/carb engine for now with the possibility for a little spray. I am still gathering the last few parts and hope to have it running shortly.
2000 Mustang GT
6.0 LQ4 Carbed/Cammed
t400- 3500 stall
3.73 gear
I picked up a car with an engine noise for cheap and am throwing together an LQ4 (also picked up cheap!)
For the swap I went with an AJE k-member/mounts, UPR a-arms and coilovers. The car is going to be a cam/carb engine for now with the possibility for a little spray. I am still gathering the last few parts and hope to have it running shortly.
2000 Mustang GT
6.0 LQ4 Carbed/Cammed
t400- 3500 stall
3.73 gear
Thread Starter
Launching!
iTrader: (11)
Joined: Sep 2007
Posts: 247
Likes: 0
From: Hillsdale, Michigan
I put the engine in today to check clearances with the truck accesories.
Everything looks fine. the alternator was what I was worried about but clears the cobra R hood by about 3"
Everything looks fine. the alternator was what I was worried about but clears the cobra R hood by about 3"
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Thread Starter
Launching!
iTrader: (11)
Joined: Sep 2007
Posts: 247
Likes: 0
From: Hillsdale, Michigan
Been slowly making a go at it.
Engine and Turbo 400 trans are in and I have the driveshaft for it also.
I fell behind on the build so I am going turbo with it before it comes out.
To make that easier I switched it over to manual brakes and am also putting in a manual rack.
Underside view of F-body oilpan/AJE K-member and mounts
also went from 17's to 15's
15x4 and 15x10's (6.5 backspacing) that will be running 325/50/15s
Engine and Turbo 400 trans are in and I have the driveshaft for it also.
I fell behind on the build so I am going turbo with it before it comes out.
To make that easier I switched it over to manual brakes and am also putting in a manual rack.
Underside view of F-body oilpan/AJE K-member and mounts
also went from 17's to 15's
15x4 and 15x10's (6.5 backspacing) that will be running 325/50/15s
Thread Starter
Launching!
iTrader: (11)
Joined: Sep 2007
Posts: 247
Likes: 0
From: Hillsdale, Michigan
still working away on the car...
It has been a slow go at it but I have been doing things whenever I get extra money to spend on it
I have most of the parts.... (just lacking driveshaft being finished, some fuel parts, and wiring)
The car now has full TeamZ rear suspension with antiroll bar, 325 MT drag radials
engine is going back in then I will start the fuel system. finish up minor odds and ends and it should be going soon.
I wanted the shifter to be in the stock location and with a little work was able to get a Pro stick in there..
Using an 1/8" plate I got the shifter in with minimal trimming, and mounted the B&M cover after powder coating it flat black with leather covered brackets to fill in the stock hole. I get full movement with the trigger just touching the bezel in park
It has been a slow go at it but I have been doing things whenever I get extra money to spend on it
I have most of the parts.... (just lacking driveshaft being finished, some fuel parts, and wiring)
The car now has full TeamZ rear suspension with antiroll bar, 325 MT drag radials
engine is going back in then I will start the fuel system. finish up minor odds and ends and it should be going soon.
I wanted the shifter to be in the stock location and with a little work was able to get a Pro stick in there..
Using an 1/8" plate I got the shifter in with minimal trimming, and mounted the B&M cover after powder coating it flat black with leather covered brackets to fill in the stock hole. I get full movement with the trigger just touching the bezel in park
Thread Starter
Launching!
iTrader: (11)
Joined: Sep 2007
Posts: 247
Likes: 0
From: Hillsdale, Michigan
I got the engine/trans back in for hopefully the last time and started on getting the radiator, headers, hoses in.
Made a radiator bracket it seems to have worked out good.
Made a radiator bracket it seems to have worked out good.
Thread Starter
Launching!
iTrader: (11)
Joined: Sep 2007
Posts: 247
Likes: 0
From: Hillsdale, Michigan
still working away when I get time
I now have a 15 gallon cell mounted into the trunk floor and put the rear firewall in (running a seat delete)
The dash/interior are now out and I am doing a complete harness eliminating all of the extra garbage. I hope to have that done over the next week.
the car then needs the driveshaft finished, speedo/tach and fuelpump installed
Hopefully it is running shortly
I now have a 15 gallon cell mounted into the trunk floor and put the rear firewall in (running a seat delete)
The dash/interior are now out and I am doing a complete harness eliminating all of the extra garbage. I hope to have that done over the next week.
the car then needs the driveshaft finished, speedo/tach and fuelpump installed
Hopefully it is running shortly