Alternator stops charging at high rpms
#1
Alternator stops charging at high rpms
I'm running a truck 105 alt in my Mustang/Lq9 combo and I have an issue that persists - alternator stops charging at high rpms, and comes back on as the rpms dips. I have a reman Autozone alternator. Got another one, same exact thing. Got a larger alt. pulley as reasearch shows that these things can be over-spun, same thing. I have a resistance wire to the "L" terminal, and I ran another wire with a light to the same terminal just to make sure the alternator is excited. Only thing left is to get an even bigger alternator pulley to slow it down further but nobody else seems to have an issue so it must be something I'm doing. Maybe I need a NEW, as in brand-new alternator???
Anything under ~6000 and it charges rock-solid at 14.4+ volts
Anything under ~6000 and it charges rock-solid at 14.4+ volts
#4
TECH Fanatic
iTrader: (44)
My Alt just crapped out on me too! I am following this thread...
https://ls1tech.com/forums/generatio...failure-s.html
https://ls1tech.com/forums/generatio...failure-s.html
#5
My Alt just crapped out on me too! I am following this thread...
https://ls1tech.com/forums/generatio...failure-s.html
https://ls1tech.com/forums/generatio...failure-s.html
#7
11 Second Club
iTrader: (11)
Join Date: Aug 2005
Location: St. Petersburg, FL
Posts: 574
Likes: 0
Received 0 Likes
on
0 Posts
The problem is the cheap *** rectifier they use in the remans even the expensive remans are crap. Order a 4200hd rectifier with 70amp diodes and swap it into a autozone lifetime warranty alt. That's what I'm running.
Trending Topics
#8
TECH Junkie
iTrader: (9)
I had that problem with multiple alternators; didn't matter if it was one from the dealer, Pep Boys, parts store, truck alternator, locally rebuilt, etc. Didn't go away until I installed a 2.75" underdrive pulley, but now I need to spin the motor a little faster to match the factory charging rate at idle. I never get 14.4V even on a 'new' alternator with 0/1 gauge wiring, typically it's upper 12's or low 13's. Thought about buying a Powermaster which is supposedly guaranteed to a alternator shaft RPM of 18K, but I'm not crazy about the inconvenience of potential mail order warranty service. Where do you order the 4200HD 70A rectifiers?
#12
11 Second Club
iTrader: (11)
Join Date: Aug 2005
Location: St. Petersburg, FL
Posts: 574
Likes: 0
Received 0 Likes
on
0 Posts
The rectifiers can overheat at higher rpms the nicer ones have a better heat sink.
But other issues could be brush run out and belt slip. Sounds like you might have a brush issue.
But other issues could be brush run out and belt slip. Sounds like you might have a brush issue.
#14
So the question is, what's the best approach? New alternator say from Powermaster, get an even bigger alt pulley (currently 2.75", have to go to say 3.5") but worried about charging at idle.
#16
TECH Enthusiast
iTrader: (1)
Not charging
I noticed at some NASCAR events the battery would die and got me to thinking why. Because of the constant high RPM maybe the alternator isn't putting out for some reason. Finally came to the conclusion the brushes were being blown or bounced away thereby causing a no charge situation. What about more spring pressure? Either add shims or stretch the existing ones.
#17
My last LQ9 blew a hole through the block at ~130mph for no obvious reason. One theory is that b/c the alternator was not charging, battery votage dipped down to 12.4v. Coulda had some kind of misfire that blew the engine apart (AFR, fuel, oil pressures were all good when she let go).
#18
I noticed at some NASCAR events the battery would die and got me to thinking why. Because of the constant high RPM maybe the alternator isn't putting out for some reason. Finally came to the conclusion the brushes were being blown or bounced away thereby causing a no charge situation. What about more spring pressure? Either add shims or stretch the existing ones.
#19
I called Powemaster and spoke to a real nice fellow over there, and he feels I just may plain be running outta amperage at high rpms between the injectors(low imp), 2 fuel pumps, EFI, elec fan and 2 fuel pumps. He suggested a 165a alt that will drop-in.
Do you guys think 105a that I currently run insufficient? The fellow doesn't think this alternator is even putting that out!
Do you guys think 105a that I currently run insufficient? The fellow doesn't think this alternator is even putting that out!