CORBRETTA is born!
04-09-2006, 12:04 AM
#41
Launching!
Thread Starter
Join Date: Feb 2006
Location: OHIO
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
I need help with exhaust exit based on C5 Corvette.
http://www.beretta.net/board/ib3/iko...9;t=261;st=195
http://www.beretta.net/board/ib3/iko...9;t=261;st=195
Last edited by Norm '88 GT; 04-09-2006 at 12:12 AM.
04-13-2006, 11:35 AM
#42
Launching!
Thread Starter
Join Date: Feb 2006
Location: OHIO
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
Question on flywheel torque procedure. It requires 52 ft. lbs. at the end of the fouth sequence of tightening.
What should be the torque leading up to that? Loctite Blue is waiting.
What should be the torque leading up to that? Loctite Blue is waiting.
04-13-2006, 11:58 AM
#43
TECH Fanatic
iTrader: (1)
Join Date: Dec 2003
Location: Farmington Hills, MI
Posts: 1,098
Likes: 0
Received 0 Likes
on
0 Posts
Flywheel
http://www.ls1howto.com/index.php?category=1
Engine Flywheel Bolts (First Pass) 15 lb ft
Engine Flywheel Bolts (Second Pass) 37 lb ft
Engine Flywheel Bolts (Final Pass) 74 lb ft
Pressure Plate
http://www.installuniversity.com/ins...ch_install.htm
Install new flywheel and torque the 6 bolts progressively to 74 ft-lbs in a criss-cross pattern. Use a flywheel tool (or equivalent to hold the flywheel during torqing. (sorry no picture) Clean the surfaces the clutch will touch on the flywheel and pressure plate with brake cleaner. DO NOT touch these surfaces after cleaning. DO NOT touch the clutch lining! Oil/grease will reduce clutch life and hinder performance of the clutch!
Use a clutch alignment tool to hold the clutch in position and then install the new pressure plate tightening the bolts to 52 ft-lbs in a criss-cross pattern.
http://www.ls1howto.com/index.php?category=1
Engine Flywheel Bolts (First Pass) 15 lb ft
Engine Flywheel Bolts (Second Pass) 37 lb ft
Engine Flywheel Bolts (Final Pass) 74 lb ft
Pressure Plate
http://www.installuniversity.com/ins...ch_install.htm
Install new flywheel and torque the 6 bolts progressively to 74 ft-lbs in a criss-cross pattern. Use a flywheel tool (or equivalent to hold the flywheel during torqing. (sorry no picture) Clean the surfaces the clutch will touch on the flywheel and pressure plate with brake cleaner. DO NOT touch these surfaces after cleaning. DO NOT touch the clutch lining! Oil/grease will reduce clutch life and hinder performance of the clutch!
Use a clutch alignment tool to hold the clutch in position and then install the new pressure plate tightening the bolts to 52 ft-lbs in a criss-cross pattern.
04-15-2006, 11:01 PM
#45
Launching!
Thread Starter
Join Date: Feb 2006
Location: OHIO
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
Ready to bolt it down and start on the interior:
http://www.beretta.net/board/ib3/iko...r=1;&#entry223
http://www.beretta.net/board/ib3/iko...r=1;&#entry223
04-17-2006, 11:51 AM
#46
Launching!
Thread Starter
Join Date: Feb 2006
Location: OHIO
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
04-29-2006, 07:57 PM
#47
Launching!
Thread Starter
Join Date: Feb 2006
Location: OHIO
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
Last edited by Norm '88 GT; 04-30-2006 at 05:30 PM.
05-06-2006, 08:15 PM
#49
Launching!
Thread Starter
Join Date: Feb 2006
Location: OHIO
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
06-24-2006, 08:51 AM
#51
Launching!
Thread Starter
Join Date: Feb 2006
Location: OHIO
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
Sorry about the delay. I would have had it running by now but I got side tracked.
http://i29.photobucket.com/albums/c2...T/c5-black.jpg
http://i29.photobucket.com/albums/c2.../c5-black2.jpg
To add to the latest project I am moving so the Beretta is on indefinite hold.
But I'll be back!!!!
http://i29.photobucket.com/albums/c2...T/c5-black.jpg
http://i29.photobucket.com/albums/c2.../c5-black2.jpg
To add to the latest project I am moving so the Beretta is on indefinite hold.
But I'll be back!!!!
06-24-2006, 06:42 PM
#52
On The Tree
iTrader: (1)
Join Date: May 2005
Location: Oregon
Posts: 177
Likes: 0
Received 0 Likes
on
0 Posts
Hey, I didn't read your entire thread at the beretta forum. Did you extend the torque tube/shaft? It looks like you just moved the engine back to avoid that. Couldn't tell for sure from what I saw. I need to have mine extended and I'm finding that no machine-shop or drive-line shop wants to do it.
06-24-2006, 08:38 PM
#53
Launching!
Thread Starter
Join Date: Feb 2006
Location: OHIO
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Frizzle Fry
Hey, I didn't read your entire thread at the beretta forum. Did you extend the torque tube/shaft? It looks like you just moved the engine back to avoid that. Couldn't tell for sure from what I saw. I need to have mine extended and I'm finding that no machine-shop or drive-line shop wants to do it.
Norm
06-27-2006, 11:11 PM
#54
For torque tube lengthening check this out.
http://www.seriouswheels.com/top-196...o-Jay-Leno.htm
Looks like a guy named Bernard Juchli lengthened the torque tube 14 inches. His home number is 626-355-0587.
Tim
http://www.seriouswheels.com/top-196...o-Jay-Leno.htm
Looks like a guy named Bernard Juchli lengthened the torque tube 14 inches. His home number is 626-355-0587.
Tim
Last edited by sierrac3_s2000; 06-28-2006 at 10:20 AM.
08-01-2007, 02:55 PM
#55
Originally Posted by sierrac3_s2000
For torque tube lengthening check this out.
http://www.seriouswheels.com/top-196...o-Jay-Leno.htm
Looks like a guy named Bernard Juchli lengthened the torque tube 14 inches. His home number is 626-355-0587.
Tim
http://www.seriouswheels.com/top-196...o-Jay-Leno.htm
Looks like a guy named Bernard Juchli lengthened the torque tube 14 inches. His home number is 626-355-0587.
Tim
bad link, it's not working.
*** edit *** this one ---> http://www.seriouswheels.com/cars/to...o-Jay-Leno.htm
