My LS1 RX7 Build
05-08-2007, 03:35 AM
#123
Originally Posted by Snyper
I just sold my trans am and bought a 93 red/black interior FD..cant wait to get started..i might be annoying you for a million questions. haha
05-08-2007, 06:46 PM
#125
Well here goes
Roller 3K need some parts but most everything was there.
Motor/Trans 3500
conversion parts 2885
Headers 960
Bushings 500
random parts 1K
Cam 330
pushrods 130
springs 175
timming chain 150
Spec Clutch 425
Alu flywheel 315
Exhaust 115 (Ebay rules)
Brakes 275
Tune 450
Nitrous kit 650
and there is more I think I hit the 15K mark by now and i know I will be over it after paint tires and the exhaust shop. Then later I will be doing more to the suspension with coil-overs and swaybars.
Roller 3K need some parts but most everything was there.
Motor/Trans 3500
conversion parts 2885
Headers 960
Bushings 500
random parts 1K
Cam 330
pushrods 130
springs 175
timming chain 150
Spec Clutch 425
Alu flywheel 315
Exhaust 115 (Ebay rules)
Brakes 275
Tune 450
Nitrous kit 650
and there is more I think I hit the 15K mark by now and i know I will be over it after paint tires and the exhaust shop. Then later I will be doing more to the suspension with coil-overs and swaybars.
05-09-2007, 12:31 AM
#126
10 Second Club
iTrader: (27)
Join Date: Nov 2006
Location: Connecticut
Posts: 1,905
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Dragframe
how much do these cars go for? i think i may have to build me a badass DD...
I paid $5500 for the roller.but it came with brand new brembo brakes/braided lines,new greddy Type S coilovers($1500) and **** load of guages which ill sell,a 3" full stainless exhaust(sell too) and a few other things ill sell. It has 63k miles on it and needs a few interior pieces which are damn hard to find.Its red now but im unsure of the future color of the car.
Last edited by Snyper; 05-18-2007 at 02:27 AM.
05-12-2007, 09:59 AM
#128
ok guys I got my CAI in and I worked on mounted it yesterday. I have a 4" intake pipe with elbows and a velocity stack. I spent some time modifying the MAF sensor to fit into the 4" pipe with out restricting flow, this was fun. The intake was ment to be for a speed density tune but I wanted to stay away from that and still have the flow I needed.
Here is the new mounting for the MAF I cut it down to nothing but the hot wires and did not damage it. I had to then cut a 3/16" X 7/8" hole to insert the sensor into the pipe.
I also relocated the front fuse box to allow more room for the AC.
this is going to be right behind the bumper core support so it should be well protected also.
Here is the new mounting for the MAF I cut it down to nothing but the hot wires and did not damage it. I had to then cut a 3/16" X 7/8" hole to insert the sensor into the pipe.
I also relocated the front fuse box to allow more room for the AC.
this is going to be right behind the bumper core support so it should be well protected also.
05-18-2007, 02:28 AM
#129
10 Second Club
iTrader: (27)
Join Date: Nov 2006
Location: Connecticut
Posts: 1,905
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by bursty
I paid $7300 for my roller, but it had a brand new paint job and low miles (58k).
Good luck with the swap Snyper! Keep us updated over on the SCT and V8 RX7 forums.
Good luck with the swap Snyper! Keep us updated over on the SCT and V8 RX7 forums.
Will do..ill have pics of the car tomorrow or saturday.
