So here's the game plan 00 Mustang + LSx + huge turbo :)
07-17-2007, 05:12 PM
#241
9 Second Club
iTrader: (15)
Join Date: Jan 2005
Location: waldorf,md
Posts: 1,063
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Phil99vette
Yeah, if you saw it you would probably call "BS" on what I paid for most of my stuff. Its really not as high as most would expect. I've gotten deals on almost 100% of the parts I have gotten. My old corvette motor, wheels/tires, nitrous and misc paid for most of the stuff.
just kidding phil .... I had to pull the flag since you said so. I'll try and sneek over this weekend and check it out in person. Ken
07-18-2007, 01:16 PM
#243
Got a few more little goodies on the way from Summit, Jegs and Moser Engineering.
Moser Rear End Brace
TheV 16/12 volt Lite battery
Handful of (-12) (-10) (-8) Black Summit Fittings straight 45 and 90
-12an to -10 O-ring adapter for fuel pump
-8 and -10 Plugs and adapters for the regulator
-8 -10 and -12 SS hose
Single -12 to dual -10 Y block from Jegs for fuel tank
Single -10 to dual -7 Y block from Jegs for fuel rails
Moser Rear End Brace
TheV 16/12 volt Lite battery
Handful of (-12) (-10) (-8) Black Summit Fittings straight 45 and 90
-12an to -10 O-ring adapter for fuel pump
-8 and -10 Plugs and adapters for the regulator
-8 -10 and -12 SS hose
Single -12 to dual -10 Y block from Jegs for fuel tank
Single -10 to dual -7 Y block from Jegs for fuel rails
07-24-2007, 02:40 PM
#245
Knocked out a couple of things this morning:
- Mocked up upper IC pipe still needs to be bead rolled and welded
- Cut floor for thru floor rear cross-member & installed rear cross member
- started mocking up cage for custom window net
- Removed stud and mocked up brake pedal for manual conversion
- Installed auto brake and gas pedal & welded on tab for carb throttle cable
- welded passenger side collector - passenger side header is 90% done now
- welded rear brace on Moser 9"
- welded rear sway bar tabs on rear end
- filled in holes on rear wing with fiberglass and started body work on rear facia, driver door to remove 3 small dings
- Intake manifold is done except for some spacers between the mounts and the fuel rail tabs, I had a local shop drill the injector bungs and we tapped the mounts
- cut plate for blockoff to close hole for manual shifter in center console
- made tab for throttle cable to firewall
- Mounts for radiator are ready to be mocked up
Motor is done @ the machine shop, I need to pick it up and take it to have the o-ring installed
- Mocked up upper IC pipe still needs to be bead rolled and welded
- Cut floor for thru floor rear cross-member & installed rear cross member
- started mocking up cage for custom window net
- Removed stud and mocked up brake pedal for manual conversion
- Installed auto brake and gas pedal & welded on tab for carb throttle cable
- welded passenger side collector - passenger side header is 90% done now
- welded rear brace on Moser 9"
- welded rear sway bar tabs on rear end
- filled in holes on rear wing with fiberglass and started body work on rear facia, driver door to remove 3 small dings
- Intake manifold is done except for some spacers between the mounts and the fuel rail tabs, I had a local shop drill the injector bungs and we tapped the mounts
- cut plate for blockoff to close hole for manual shifter in center console
- made tab for throttle cable to firewall
- Mounts for radiator are ready to be mocked up
Motor is done @ the machine shop, I need to pick it up and take it to have the o-ring installed
07-26-2007, 07:11 PM
#251
I've got alot more pic's coming. I did ALOT of work today and made alot of progress. Motor is done @ the machine shop and just needs to be taken to Jackson to get the CNC o-ring installed.
Sway bar was orginally installed but the bar was too low and we couldn't get the tires tucked up under the car enough so I cut it out and started fresh. I raised the bar about 2" and made some custom plates. The suspension will basically bottom out on the frame rails now.
I may need to move the front upper control arm points up slightly.
Passenger side swaybar mockup
Overall Mockup shot
Making the sway bar plates
Tig - Swaybar cup weld
Swaybar end plates finished ready for installation
Mig - Swaybar mount weld
Just got battery - will mockup mounts and box this weekend
Mockup for custom window net from M & R products, template leaves tomorrow - turnaround time 1 week
New pedals with tab for pull style carb cable
Interior shot
Driver side motor starting to look like a motor
Driver header collector shot - getting closer
Rear crossmember - thru floor design
3000hp intercooler under dash
Shifter blockout plate
Rear cage X bars to be installed this weekend
rear cage underside 2 x 3 outriggers - rear crossmember
Rear torque box plates
Sway bar was orginally installed but the bar was too low and we couldn't get the tires tucked up under the car enough so I cut it out and started fresh. I raised the bar about 2" and made some custom plates. The suspension will basically bottom out on the frame rails now.
I may need to move the front upper control arm points up slightly.Passenger side swaybar mockup
Overall Mockup shot
Making the sway bar plates
Tig - Swaybar cup weld
Swaybar end plates finished ready for installation
Mig - Swaybar mount weld
Just got battery - will mockup mounts and box this weekend
Mockup for custom window net from M & R products, template leaves tomorrow - turnaround time 1 week
New pedals with tab for pull style carb cable
Interior shot
Driver side motor starting to look like a motor
Driver header collector shot - getting closer
Rear crossmember - thru floor design
3000hp intercooler under dash
Shifter blockout plate
Rear cage X bars to be installed this weekend
rear cage underside 2 x 3 outriggers - rear crossmember
Rear torque box plates
Last edited by Phil99vette; 10-17-2007 at 04:26 PM.
07-26-2007, 07:41 PM
#253
I've got alot more pic's coming. I did ALOT of work today and made alot of progress. Motor is done @ the machine shop and just needs to be taken to Jackson to get the CNC o-ring installed.
Sway bar was orginally installed but the bar was too low and we couldn't get the tires tucked up under the car enough so I cut it out and started fresh. I raised the bar about 2" and made some custom plates. The suspension will basically bottom out on the frame rails now. I may need to move the front upper control arm points up slightly.
Passenger side swaybar mockup
Overall Mockup shot
Making the sway bar plates
Tig - Swaybar cup weld
Swaybar end plates finished ready for installation
Mig - Swaybar mount weld
Just got battery - will mockup mounts and box this weekend
Mockup for custom window net from M & R products, template leaves tomorrow - turnaround time 1 week
New pedals with tab for pull style carb cable
Interior shot
Driver side motor starting to look like a motor
Driver header collector shot - getting closer
Rear crossmember - thru floor design
3000hp intercooler under dash
Shifter blockout plate
Rear cage X bars to be installed this weekend
rear cage underside 2 x 3 outriggers - rear crossmember
Rear torque box plates
Sway bar was orginally installed but the bar was too low and we couldn't get the tires tucked up under the car enough so I cut it out and started fresh. I raised the bar about 2" and made some custom plates. The suspension will basically bottom out on the frame rails now.
I may need to move the front upper control arm points up slightly.Passenger side swaybar mockup
Overall Mockup shot
Making the sway bar plates
Tig - Swaybar cup weld
Swaybar end plates finished ready for installation
Mig - Swaybar mount weld
Just got battery - will mockup mounts and box this weekend
Mockup for custom window net from M & R products, template leaves tomorrow - turnaround time 1 week
New pedals with tab for pull style carb cable
Interior shot
Driver side motor starting to look like a motor
Driver header collector shot - getting closer
Rear crossmember - thru floor design
3000hp intercooler under dash
Shifter blockout plate
Rear cage X bars to be installed this weekend
rear cage underside 2 x 3 outriggers - rear crossmember
Rear torque box plates
Last edited by Phil99vette; 10-17-2007 at 04:25 PM.
07-28-2007, 01:13 AM
#257
Staging Lane
iTrader: (3)
Join Date: Jul 2004
Location: SS Indianapolis,In.
Posts: 94
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by LSInnovations
How the hell do you get so much done in a day???? Geez, do you want a job?
Is there any ETA when it will hit the track?
