Stenod Performance weld-in 6 and 8 point roll bar kits!!
07-05-2006, 05:48 PM
#61
LS1TECH Sponsor
Thread Starter
iTrader: (1)
Join Date: Jan 2002
Location: Troy, MI
Posts: 431
Likes: 0
Received 0 Likes
on
0 Posts
Yep, this is for sure still a go. Were just catching up on work that needs to get completed before we fire out all these cages. As it looks right now, were going to start building them early next week. I have three confirmed orders and many PM's to respond too. The holiday weekend for sure cuased us to get behind, not to mention that I wasn't in the office due to my recent personal issues I dealt with this weedend. Thursday I will be returning phone calls as well as PM's. Sorry agian guys for the confusion and delay. But we are back on track after tonight and we will be going head over heals on the roll bars and cages that guys need and would like to order.
Just to clear things up too, to get a kit on order, until we get the internet ordering set up, you MUST call the shop or send me a check with a list of exactly what you want. I would prefer you guys call the shop and we'll get everything setup so nothing gets confused or missed during your order.
Thanks guys.
Can't wait to start getting some of the roll bars and cages shipped out, were all excited over here at the shop
Stenod
Just to clear things up too, to get a kit on order, until we get the internet ordering set up, you MUST call the shop or send me a check with a list of exactly what you want. I would prefer you guys call the shop and we'll get everything setup so nothing gets confused or missed during your order.
Thanks guys.
Can't wait to start getting some of the roll bars and cages shipped out, were all excited over here at the shop
Stenod
07-05-2006, 05:49 PM
#62
LS1TECH Sponsor
Thread Starter
iTrader: (1)
Join Date: Jan 2002
Location: Troy, MI
Posts: 431
Likes: 0
Received 0 Likes
on
0 Posts
3 feet of mild steel weighed in at 7lbs on our corner scales
3 feet of chromoly weighed in at 4lbs on our corner scales.
Pretty big wieght difference.
Stenod
3 feet of chromoly weighed in at 4lbs on our corner scales.
Pretty big wieght difference.
Stenod
07-18-2006, 08:51 AM
#69
LS1TECH Sponsor
Thread Starter
iTrader: (1)
Join Date: Jan 2002
Location: Troy, MI
Posts: 431
Likes: 0
Received 0 Likes
on
0 Posts
Guys-
For those that have their orders in already here is a news brief.... I have ran the transactions for the initial 10 orders and are prepared to start bvending up the kits and getting them notched. We have had a slight delay in recieving the material for the kits. It will be here This friday the 21st. Delivery was suppose to take place last friday, but we got pushed back somehow with the steel mill. Just wanted to update everyone with our current situation.
Thanks agian
Stenod
For those that have their orders in already here is a news brief.... I have ran the transactions for the initial 10 orders and are prepared to start bvending up the kits and getting them notched. We have had a slight delay in recieving the material for the kits. It will be here This friday the 21st. Delivery was suppose to take place last friday, but we got pushed back somehow with the steel mill. Just wanted to update everyone with our current situation.
Thanks agian
Stenod
07-18-2006, 02:50 PM
#70
Originally Posted by Stenod@StenodPerformance
Guys-
For those that have their orders in already here is a news brief.... I have ran the transactions for the initial 10 orders and are prepared to start bvending up the kits and getting them notched. We have had a slight delay in recieving the material for the kits. It will be here This friday the 21st. Delivery was suppose to take place last friday, but we got pushed back somehow with the steel mill. Just wanted to update everyone with our current situation.
Thanks agian
Stenod
For those that have their orders in already here is a news brief.... I have ran the transactions for the initial 10 orders and are prepared to start bvending up the kits and getting them notched. We have had a slight delay in recieving the material for the kits. It will be here This friday the 21st. Delivery was suppose to take place last friday, but we got pushed back somehow with the steel mill. Just wanted to update everyone with our current situation.
Thanks agian
Stenod
07-18-2006, 09:24 PM
#72
TECH Addict
iTrader: (4)
Join Date: Sep 2002
Location: Boise, ID
Posts: 2,542
Likes: 0
Received 0 Likes
on
0 Posts
these are some nice kits, if i didnt already have the wolfe 10pt kit on my car i would be getting one, and your install price is killer, local shop charged me 1100 to tig my cage in with the car stripped
07-24-2006, 10:27 AM
#74
TECH Fanatic
iTrader: (3)
Join Date: Feb 2005
Location: Naples, FL
Posts: 1,118
Likes: 0
Received 0 Likes
on
0 Posts
So how much for a 8pt pre notched, mild steel?
Any better pics of the rear bars and the t-top area clearance?
I have a sub in the small cubby area on the drivers side of the t-top well, and my battery be relocated to the spare tire area on the passenger side shortly...
If I can keep my sub, t-top holder use, and access to the battery, Id definitely get your kit. I dont like the only options with wolfe being the deck or wheel well area, and def prefer to have the bars weld to the subframe.
Nice job guys, the best kit Ive seen so far IMO.
Any better pics of the rear bars and the t-top area clearance?
I have a sub in the small cubby area on the drivers side of the t-top well, and my battery be relocated to the spare tire area on the passenger side shortly...
If I can keep my sub, t-top holder use, and access to the battery, Id definitely get your kit. I dont like the only options with wolfe being the deck or wheel well area, and def prefer to have the bars weld to the subframe.
Nice job guys, the best kit Ive seen so far IMO.
07-26-2006, 04:35 PM
#76
Joe is on the road right now delivering and picking up a couple cars for customers.
I do know the guys at the shop have been busy on them. 6 nearly complete kits were lined up last night when I was there. Looked like a couple door bars and the weld plates were the last remaining pieces.
Not sure who's they are, as I was just in and out after hours.
Just FYI
I do know the guys at the shop have been busy on them. 6 nearly complete kits were lined up last night when I was there. Looked like a couple door bars and the weld plates were the last remaining pieces.
Not sure who's they are, as I was just in and out after hours.
Just FYI
07-26-2006, 05:03 PM
#77
Originally Posted by y2khawk
Joe is on the road right now delivering and picking up a couple cars for customers.
I do know the guys at the shop have been busy on them. 6 nearly complete kits were lined up last night when I was there. Looked like a couple door bars and the weld plates were the last remaining pieces.
Not sure who's they are, as I was just in and out after hours.
Just FYI
I do know the guys at the shop have been busy on them. 6 nearly complete kits were lined up last night when I was there. Looked like a couple door bars and the weld plates were the last remaining pieces.
Not sure who's they are, as I was just in and out after hours.
Just FYI
07-26-2006, 05:22 PM
#78
Launching!
iTrader: (6)
Join Date: Nov 2001
Location: Commerce, MI
Posts: 230
Likes: 0
Received 0 Likes
on
0 Posts
We will be shipping all of the cage kits on Friday the 28th. Just finishing up a couple bars on the last few kits. ! Sorry for the wait, but like Joe said we got are material later than we expected and unfortunatley set us back! I should have shipping prices for everyone tomorrow. Thanks!
Kevin
Stenod Performance
! Sorry for the wait, but like Joe said we got are material later than we expected and unfortunatley set us back! I should have shipping prices for everyone tomorrow. Thanks!Kevin
Stenod Performance
07-26-2006, 06:02 PM
#79
Originally Posted by 1BADWS6@STENOD
We will be shipping all of the cage kits on Friday the 28th. Just finishing up a couple bars on the last few kits. ! Sorry for the wait, but like Joe said we got are material later than we expected and unfortunatley set us back! I should have shipping prices for everyone tomorrow. Thanks!
Kevin
Stenod Performance
! Sorry for the wait, but like Joe said we got are material later than we expected and unfortunatley set us back! I should have shipping prices for everyone tomorrow. Thanks!Kevin
Stenod Performance
Can I get some Stenod Performance stickers for my car? 
And a shirt 
07-27-2006, 05:55 AM
#80
9 Second Club
iTrader: (17)
Join Date: Nov 2002
Location: New Braunfels ,Tx
Posts: 4,997
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by y2khawk
Joe is on the road right now delivering and picking up a couple cars for customers.
I do know the guys at the shop have been busy on them. 6 nearly complete kits were lined up last night when I was there. Looked like a couple door bars and the weld plates were the last remaining pieces.
Not sure who's they are, as I was just in and out after hours.
Just FYI
I do know the guys at the shop have been busy on them. 6 nearly complete kits were lined up last night when I was there. Looked like a couple door bars and the weld plates were the last remaining pieces.
Not sure who's they are, as I was just in and out after hours.
Just FYI
Im allready tearing up my car again LOL It never ends 
And I will take 2 silver Stenod stickers and hook me up with 2 XL Stenod shirts please. Once the boys around here see the cages we will be hitting you up Im sure of it Come on I know you have some big boy shirts Last edited by JMBLOWNWS6; 07-27-2006 at 06:01 AM.