Cam Only Dyno Thread
#521
10 Second Club
Very nice!
#522
On The Tree
iTrader: (2)
Join Date: Sep 2009
Location: Elgin, South Carolina
Posts: 103
Likes: 0
Received 0 Likes
on
0 Posts
99 SS 6 Speed on Skinnys & Fattys 4.10 Gear..
Tick SNS Stage 3 Cam
853 Heads
26# Injectors
Lid
P/S Delete
A/C Delete
Fernco Bellow
Tsp 1 7/8 LT's
Open X Pipe
Made 384/363...
Now Has Ported TB & LS6 Intake.. But No New Numbers..
Drivability is OK.. Bucks pretty good at low speed... Gets into power at 3000 an pulls hard to the top!
Tick SNS Stage 3 Cam
853 Heads
26# Injectors
Lid
P/S Delete
A/C Delete
Fernco Bellow
Tsp 1 7/8 LT's
Open X Pipe
Made 384/363...
Now Has Ported TB & LS6 Intake.. But No New Numbers..
Drivability is OK.. Bucks pretty good at low speed... Gets into power at 3000 an pulls hard to the top!
#524
10 Camaro SS LS3 ARH Long tubes w/cat delete, CAI, BTR 3 cam package 480 rwhp 447 rwtq
Dyno sheet link http://prntscr.com/ax7wzg
Dyno sheet link http://prntscr.com/ax7wzg
#526
2002 Z28
TSP Torquer V4 (231/234 .629/.615 111LSA)
M6 - 4:10
TSP 1 7/8 Longtubes
TSP Catted Y - dumped after axle
SLP 90mm MAF
FTP 98mm Lid
Stock LS6 Intake- Stock throttle body
400RWHP/353RWTQ
TSP Torquer V4 (231/234 .629/.615 111LSA)
M6 - 4:10
TSP 1 7/8 Longtubes
TSP Catted Y - dumped after axle
SLP 90mm MAF
FTP 98mm Lid
Stock LS6 Intake- Stock throttle body
400RWHP/353RWTQ
Last edited by 02M6Z28; 05-06-2016 at 10:34 AM.
#531
1973 Corvette
Stock bottom 5.3
228r texas speed racing cam
243 heads milled .017
ls6 intake and tb
Beehive springs
2600-2900 stall
1 3/4 long tube headers
Custom tune
Th400
3.08 posi gears
350rwhp
312rwtq
Stock bottom 5.3
228r texas speed racing cam
243 heads milled .017
ls6 intake and tb
Beehive springs
2600-2900 stall
1 3/4 long tube headers
Custom tune
Th400
3.08 posi gears
350rwhp
312rwtq
#532
LS2 gto, PatG grind 235/243 .629/.629 112lsa, TSP cnc ported stock 243 castings, FAST 92mm intake, pacesetter long tube headers through stock resonator and 2.5" exhaust (need me an X pipe). made 440/406!
#535
Teching In
Join Date: Sep 2016
Location: North Carolina
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
1998 Formula M6
Tick SNS Stage 3 mild lobes
LS6 Intake
SLP lid
Ported throttle body
Speed Engineering long tubes
ORY pipe
Flowmasters
Stock heads, stock injectors, stock 3.42 rear, stock clutch
390hp 380tq
Cam install and tune by Steve Williams(Tuned by frost)
Tick SNS Stage 3 mild lobes
LS6 Intake
SLP lid
Ported throttle body
Speed Engineering long tubes
ORY pipe
Flowmasters
Stock heads, stock injectors, stock 3.42 rear, stock clutch
390hp 380tq
Cam install and tune by Steve Williams(Tuned by frost)
Last edited by punkysable; 12-12-2016 at 04:42 AM.
#536
On The Tree
Join Date: Jul 2005
Location: corpus christi, Tx
Posts: 182
Likes: 0
Received 0 Likes
on
0 Posts
1999 z28 m6
slp lid, tsp tsunami cam, tsp 1 3/4 long tubes w/ORY, flowmaster exhaust, stock ls1 tb/intake manifold, stock 241 heads
392.8/375
low speed driving can be a chore but daily driving is definitely posible even in stop and go traffic
slp lid, tsp tsunami cam, tsp 1 3/4 long tubes w/ORY, flowmaster exhaust, stock ls1 tb/intake manifold, stock 241 heads
392.8/375
low speed driving can be a chore but daily driving is definitely posible even in stop and go traffic
Last edited by 05GMC4.8; 01-15-2017 at 11:26 AM. Reason: grammar
#537
Staging Lane
2005 cts-v 6.1 lq4
I finally got to baseline my 2005 V today. The car was like this when I purchased it. Less than 9k miles on the driveline.
LQ4 bored .030" over, Mahle forged pistons, H-beam rods with ARP2000 bolts, new LS3 heads and manifold, Comp cam 219/227 112 lsa. Compression is 10.8:1.
Exhaust
Kooks 1 7/8" longtubes with Calico coating, Stainless Works full 3" with X-pipe O
And the results were:
Last edited by reeseleblanc; 02-07-2017 at 09:42 PM.
#538
TECH Enthusiast
iTrader: (13)
im in the middle of an argument on facebook with a guy claiming he made 400whp with a cam only ls1. literally cam only. no headers.
BTR Cam
upgraded valve springs. stock pushrods (which is dumb IMO)
stock LS6 intake.
I informed him I made 423/389 with a TREX cam kit, 243's, LT's, ORY, LS6 intake. he said I needed a better tuner.
so needless to say im having fun because he sounds like an idiot. agree? and if this is preferred to not be talked about here. deleting this comment is no big deal. or moved to the BS Thread.
BTR Cam
upgraded valve springs. stock pushrods (which is dumb IMO)
stock LS6 intake.
I informed him I made 423/389 with a TREX cam kit, 243's, LT's, ORY, LS6 intake. he said I needed a better tuner.
so needless to say im having fun because he sounds like an idiot. agree? and if this is preferred to not be talked about here. deleting this comment is no big deal. or moved to the BS Thread.
#539
im in the middle of an argument on facebook with a guy claiming he made 400whp with a cam only ls1. literally cam only. no headers.
BTR Cam
upgraded valve springs. stock pushrods (which is dumb IMO)
stock LS6 intake.
I informed him I made 423/389 with a TREX cam kit, 243's, LT's, ORY, LS6 intake. he said I needed a better tuner.
so needless to say im having fun because he sounds like an idiot. agree? and if this is preferred to not be talked about here. deleting this comment is no big deal. or moved to the BS Thread.
BTR Cam
upgraded valve springs. stock pushrods (which is dumb IMO)
stock LS6 intake.
I informed him I made 423/389 with a TREX cam kit, 243's, LT's, ORY, LS6 intake. he said I needed a better tuner.
so needless to say im having fun because he sounds like an idiot. agree? and if this is preferred to not be talked about here. deleting this comment is no big deal. or moved to the BS Thread.
#540
On The Tree
iTrader: (1)
Join Date: Feb 2006
Location: KCRP
Posts: 148
Likes: 0
Received 0 Likes
on
0 Posts
2000 SS M6
MTI T-1 cam: 221/221 558/558 112 with 918's
338HP/338TQ cutout closed
No Tune
Random Tech Catback
Cutout
Stock LS1 intake manifold
Stock TB
Stock MAF
Stock heads
Aftermarket lid
MTI T-1 cam: 221/221 558/558 112 with 918's
338HP/338TQ cutout closed
No Tune
Random Tech Catback
Cutout
Stock LS1 intake manifold
Stock TB
Stock MAF
Stock heads
Aftermarket lid
Last edited by Qfly; 03-02-2017 at 07:02 PM.