New bolt-on Dyno Record????
05-15-2005, 12:21 PM
#1
On The Tree
Thread Starter
iTrader: (2)
Join Date: Nov 2003
Location: Pensacola Florida
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
New bolt-on Dyno Record???? Welp, I dont know if this is a record, but its damn sure got to be close. Couple buddies of mine went to Dyno at James' at RWTD yesterday and had some great luck! My buddies car is a 98 z28 with headers, cutout, ls6 manifold, TUNE by John Weeks (John02SS).....and the majority of the rest of the bolt ons. These numbers are VERY stout out of a bolt on car. Also, there are a few board member who can testify to this, including James, the owner of RWTD. And the dyno was checked for calibrations and everything before and after he made the pulls. These numbers are CORRECTED.
379.94 HP @ 5600 rpms
388.86 ft/lbs 4400 rpms.....
Flame away fellas, but this one is real. I too have never seen anything like this. Car did not have the A/C belt on, thru a cutout.
We have dyno sheets to prove it, and im sure James wouldnt mind if you contacted him for proof. The bar has been raised fellas!
379.94 HP @ 5600 rpms
388.86 ft/lbs 4400 rpms.....
Flame away fellas, but this one is real. I too have never seen anything like this. Car did not have the A/C belt on, thru a cutout.
We have dyno sheets to prove it, and im sure James wouldnt mind if you contacted him for proof. The bar has been raised fellas!
05-15-2005, 01:31 PM
#5
On The Tree
Thread Starter
iTrader: (2)
Join Date: Nov 2003
Location: Pensacola Florida
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SILVERZZ28
James said if he tuned it could very well be..............
05-15-2005, 02:33 PM
#7
On The Tree
Thread Starter
iTrader: (2)
Join Date: Nov 2003
Location: Pensacola Florida
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
Car has:
ls6 manifold
mac headers and o/r y
cutout
B&B triflow
ported TB
ported MAF
Aluminum DS
3.73's
z06 clutch
ls6 valley cover
KNN FIPK
Tuned by John weeks (John02SS)
And thats it, typical bolt on car. Doesnt even have a pulley, and has MACs.....And the car PULLS STRONGGGG. Guess he just got a good one. Only bad part is, as we mod it more, it will probably level out with everyone.....yall know how that **** goes.
ls6 manifold
mac headers and o/r y
cutout
B&B triflow
ported TB
ported MAF
Aluminum DS
3.73's
z06 clutch
ls6 valley cover
KNN FIPK
Tuned by John weeks (John02SS)
And thats it, typical bolt on car. Doesnt even have a pulley, and has MACs.....And the car PULLS STRONGGGG. Guess he just got a good one. Only bad part is, as we mod it more, it will probably level out with everyone.....yall know how that **** goes.
Trending Topics
05-15-2005, 04:43 PM
#15
10 Second Club
iTrader: (47)
Join Date: Nov 2001
Location: Pace, FL
Posts: 1,453
Likes: 0
Received 0 Likes
on
0 Posts
I drove the car quite a bit last night and it feels pretty strong. Tune was dead nuts on with just a street tune. 13:1 AF, 29 degrees of timing. I was very surprised with the results to say the least. We even ran the car against a 400-410 rwhp car (SilverLS1) to see how we did and the out come was as would be expected with with a 25 rwhp difference.
SilverZZ28,
Damn shame I can't tune LT1's! Hell, I might could even make it fast!
SilverZZ28,
Damn shame I can't tune LT1's! Hell, I might could even make it fast!
05-15-2005, 04:45 PM
#16
Teching In
Join Date: May 2005
Location: Pensacola, FL
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
whats up everybody, the car they're talking about is mine..i couldent believe it either...anybody ever heard of one being higher?? i didnt use any kind of dyno tricks or anything. tire pressure was at 34 pounds, and no ice was used on intake. im gonna try to get the dyno sheet posted
05-15-2005, 05:29 PM
#17
TECH Apprentice
Join Date: Jan 2004
Location: Frisco TX (Dallas Area)
Posts: 337
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by MikeH Z28
whats up everybody, the car they're talking about is mine..i couldent believe it either...anybody ever heard of one being higher?? i didnt use any kind of dyno tricks or anything. tire pressure was at 34 pounds, and no ice was used on intake. im gonna try to get the dyno sheet posted
BTW, cruising in stealth mode (quiet) with the cool breezes blowing probably will cost about 25, but you are ready for a blast just by flipping a couple of switches. Maybe only one, I forget, doesn't WOT kill the AC compressor? Now that's double your fun!
05-15-2005, 05:43 PM
#18
Teching In
Join Date: Feb 2004
Posts: 47
Likes: 0
Received 0 Likes
on
0 Posts
How much did it make through the B&B Triflow?
People say it flows like crap, but I'm not so sure... I have one and I'd be interested in how much was gained from the cutout
if you didn't get numbers through the exhaust, see if you can do it next time through exhaust and through cutout to compare
People say it flows like crap, but I'm not so sure... I have one and I'd be interested in how much was gained from the cutout
if you didn't get numbers through the exhaust, see if you can do it next time through exhaust and through cutout to compare
05-15-2005, 06:03 PM
#20
Teching In
Join Date: Feb 2004
Posts: 47
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SilverLS1
it did 372 through the muffy....contrary to what alot believe, the B&B is a flowing bish.....
8 rwhp is still big enough to feel though... hhmmmm
-