02 Z28 bolton numbers
03-24-2007, 12:11 AM
#1
On The Tree
Thread Starter
Join Date: Jul 2006
Location: Alabama
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
02 Z28 bolton numbers I had my 02 M6 Z dynoed today. The car has Pacesetter LT, OR Y, Hooker catback, FTRA, my Ported TB, Bump stop mod, SLP lid I tuned the car Via HP tuners in conjunction with an XD16 wide band set up.
1) 341.34hp 348.72 FT LB
2) 342.14hp 350.30 FT LB on this run I bumped the timing up 2deg for around 5 deg total over stock @WOT
3) 344.88HP 352.26FT LB I set the timing back to my previous tune, car cooled off for 15 min.
All three runs my IAT was in the 90's the outside temp was 86deg with 13% Humidity.
What do you guys think?? I bet I could squeeze 350/354 in a little cooler weather and lower IAT's
1) 341.34hp 348.72 FT LB
2) 342.14hp 350.30 FT LB on this run I bumped the timing up 2deg for around 5 deg total over stock @WOT
3) 344.88HP 352.26FT LB I set the timing back to my previous tune, car cooled off for 15 min.
All three runs my IAT was in the 90's the outside temp was 86deg with 13% Humidity.
What do you guys think?? I bet I could squeeze 350/354 in a little cooler weather and lower IAT's
Trending Topics
03-24-2007, 09:09 PM
#9
On The Tree
Thread Starter
Join Date: Jul 2006
Location: Alabama
Posts: 127
Likes: 0
Received 0 Likes
on
0 Posts
I don’t have the dyno sheet with me at the moment but I am sure I seen SAE on there. I noticed there are quite a few guys with under drive pulleys on here. Are they worth the cost?
03-24-2007, 09:15 PM
#10
TECH Enthusiast
iTrader: (16)
Join Date: Aug 2006
Location: NC
Posts: 699
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by brantsz
I don’t have the dyno sheet with me at the moment but I am sure I seen SAE on there. I noticed there are quite a few guys with under drive pulleys on here. Are they worth the cost?
03-25-2007, 04:36 AM
#11
TECH Enthusiast
iTrader: (14)
Join Date: Oct 2003
Location: Cookeville, TN
Posts: 556
Likes: 0
Received 0 Likes
on
0 Posts
Really good numbers. With my boltons I did 340rwhp/356rwtq SAE.
I'm halfway curious if I did an ASP Pulley and re-port my TB ( i did terrible - might as well not be ported) if I could get 350rwhp.
Plus my 18" rear wheels aren't helping anything.
Very nice numbers though man! Congrats
I'm halfway curious if I did an ASP Pulley and re-port my TB ( i did terrible - might as well not be ported) if I could get 350rwhp.
Plus my 18" rear wheels aren't helping anything.
Very nice numbers though man! Congrats
03-25-2007, 06:59 AM
#12
TECH Enthusiast
iTrader: (16)
Join Date: Aug 2006
Location: NC
Posts: 699
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by JKDZ28
Really good numbers. With my boltons I did 340rwhp/356rwtq SAE.
I'm halfway curious if I did an ASP Pulley and re-port my TB ( i did terrible - might as well not be ported) if I could get 350rwhp.
Plus my 18" rear wheels aren't helping anything.
Very nice numbers though man! Congrats
I'm halfway curious if I did an ASP Pulley and re-port my TB ( i did terrible - might as well not be ported) if I could get 350rwhp.
Plus my 18" rear wheels aren't helping anything.
Very nice numbers though man! Congrats