Does My Full Bolt-on T/A Have Any Chance Against a Pullied 03 Cobra?
#1
Launching!
Thread Starter
iTrader: (7)
Join Date: Oct 2005
Location: San Diego, CA
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
Does My Full Bolt-on T/A Have Any Chance Against a Pullied 03 Cobra?
Well, I got called out by a Terminator with Intake, Xpipe, catback and a small pulley (one of the smallest ones you can put on the heaton I believe, like a 2.76). My Mods are in my sig. He wants to do dig races but I get to pick the race. He's on Nitto Dr's and I'm on BFG street tires so I'm not gonna do a dig since he'll murder me. I'm thinking my only chance is like a low roll, maybe 20-25 or something. He is also a very good driver so I can't count on !drivermod.
So do I have any chance? Is there a certain race I should choose to give my LS1 the edge?
Thanks guys!
So do I have any chance? Is there a certain race I should choose to give my LS1 the edge?
Thanks guys!
#2
As it sits you're going to lose unless he misses shifts or something. He probably has over 100 rwhp on you. Your best bet is you buy a set of slicks, go from a dig and hope you don't break your rear. Even if it all goes right he might be able to pass you by the end depending on how long the race is.
This doesn't mean that he WILL win, just that he SHOULD. Good luck if you go run him, I'm sure it'll be fun no matter which way it goes.
This doesn't mean that he WILL win, just that he SHOULD. Good luck if you go run him, I'm sure it'll be fun no matter which way it goes.
#6
With a good dyno tune (he may have a crappy email or box tune) he is laying down a good 75 (+/-) more than you and on DR's.......No way man.
Toss on a a little 50 sneaky in there, and you may have a chance.
#7
Administrator
Your only hope IMO is to go from a dig and hope he blows the tires off.
Don't let his drag radials scare you. It's not easy launching on an unprepped surface
with 450rwtq @ 2,500rpm. Do NOT run him from a 40 or a 50 roll. If you must go
from a roll, do it from about 10mph.
Don't let his drag radials scare you. It's not easy launching on an unprepped surface
with 450rwtq @ 2,500rpm. Do NOT run him from a 40 or a 50 roll. If you must go
from a roll, do it from about 10mph.
Trending Topics
#12
On The Tree
Join Date: Nov 2007
Location: West Chester, PA
Posts: 199
Likes: 0
Received 0 Likes
on
0 Posts
I have yet to race a Cobra, so this is all speculation, but I have the feeling that LS1tech users are slightly deceived by the Street Racing section into believing that Cobras aren't that big of a deal since more often than not it's a kill story for an LS1 with <50 RWHP than the Cobra.
#13
TECH Fanatic
iTrader: (18)
I have yet to race a Cobra, so this is all speculation, but I have the feeling that LS1tech users are slightly deceived by the Street Racing section into believing that Cobras aren't that big of a deal since more often than not it's a kill story for an LS1 with <50 RWHP than the Cobra.
#14
On The Tree
Join Date: Nov 2007
Location: West Chester, PA
Posts: 199
Likes: 0
Received 0 Likes
on
0 Posts
Like I said.. it was just speculation. Thanks for the nitrous kit... the car loves it.
#16
Make up an excuse as to why you can't run him this week and make it to where you run him end of next week. In the mean time find a friend with some DRs that you can borrow (or someone on here close by) and buy you a nitrous kit. Install it (I know you can hide a nitrous kit on a F-body) and between the time you get it and the time you race him learn how to use it on a 75 shot if you never have. Then when you run him spray a 75 shot with your bottle pressure up and run him at whatever mph your car is at 3,500rpms in 1st gear. Atleast this is what I'd do if I were in your shoes.
#18
11 Second Club
iTrader: (6)
I have yet to race a Cobra, so this is all speculation, but I have the feeling that LS1tech users are slightly deceived by the Street Racing section into believing that Cobras aren't that big of a deal since more often than not it's a kill story for an LS1 with <50 RWHP than the Cobra.
They are no joke in the right hands