Dyno Guesses & Bench Racing Forum Horsepower Estimates | Racing Scenarios

2011 mustang dyno and run numbers

Thread Tools
 
Search this Thread
 
Old 05-06-2010, 05:52 PM
  #21  
TECH Enthusiast
Thread Starter
 
assasinator's Avatar
 
Join Date: Oct 2009
Location: huntsville Al
Posts: 528
Likes: 0
Received 15 Likes on 15 Posts

Default

yep it did get a wheel up with a few bolt-ons. an airbag and both get up.
Old 05-06-2010, 05:53 PM
  #22  
10 Second Club
 
big hammer's Avatar
 
Join Date: May 2009
Location: over dere
Posts: 3,428
Received 153 Likes on 105 Posts

Default

i read somewhere that the 12.8 @ 111 was with some suspension work and a tune. can anyone confirm?
Old 05-06-2010, 06:13 PM
  #23  
TECH Addict
iTrader: (12)
 
chavez885's Avatar
 
Join Date: Dec 2005
Location: Concord, CA
Posts: 2,382
Likes: 0
Received 1 Like on 1 Post

Default

Originally Posted by kinglt-1
400whp @ 3500-3600lbs should trap 117-118 all day in a m6.
Originally Posted by Irunelevens
117mph with 405rwhp isn't unbelievable at all.
Duh, but how the funk is it making 405rwhp with an xpipe and a tune? I really wanna see these things myself, damn impressive if that's all that was done.
Old 05-06-2010, 06:26 PM
  #24  
TECH Enthusiast
Thread Starter
 
assasinator's Avatar
 
Join Date: Oct 2009
Location: huntsville Al
Posts: 528
Likes: 0
Received 15 Likes on 15 Posts

Default

Originally Posted by chavez885
Duh, but how the funk is it making 405rwhp with an xpipe and a tune? I really wanna see these things myself, damn impressive if that's all that was done.

the factory exhaust is restricted on purpose. its only 2.25" in several places.

368 to 405 from exhaust , tune, and filter. power is climbing at 7000 where the graph stops. its a 4v. 7000 rpm power is nothing new. the 4v in my car now loves 6900.
Old 05-09-2010, 01:01 AM
  #25  
TECH Senior Member
iTrader: (71)
 
lemons12's Avatar
 
Join Date: Jul 2007
Location: Winchester, TN
Posts: 11,088
Likes: 0
Received 2 Likes on 2 Posts

Default

That is killer times for the mods for sure...
Old 05-10-2010, 08:04 AM
  #26  
TECH Regular
 
Ke^in's Avatar
 
Join Date: Jul 2009
Location: MOV
Posts: 426
Likes: 0
Received 0 Likes on 0 Posts
Default

Damn..
Old 12-09-2010, 03:54 PM
  #27  
Teching In
 
Jonbones's Avatar
 
Join Date: Apr 2010
Posts: 0
Likes: 0
Received 0 Likes on 0 Posts
Default

I'm making a little more power than the OP, but cooler temps and 0 elevation can acct for that. I'm concerned about the stock clutch letting go on dr's. What rpm did you launch @? I'm going to the track w 26" slicks tomorrow night and am wondering if I should try to launch @ all...
Old 12-09-2010, 04:05 PM
  #28  
On The Tree
 
93sspcoupe's Avatar
 
Join Date: Jun 2010
Location: georgia
Posts: 129
Likes: 0
Received 0 Likes on 0 Posts
Default

i just want of these motors in my coupe. there is a shop in ga that did the swap. and are about to put boost on it too
Old 12-09-2010, 04:13 PM
  #29  
TECH Addict
iTrader: (12)
 
chavez885's Avatar
 
Join Date: Dec 2005
Location: Concord, CA
Posts: 2,382
Likes: 0
Received 1 Like on 1 Post

Default

Originally Posted by Jonbones
I'm making a little more power than the OP, but cooler temps and 0 elevation can acct for that. I'm concerned about the stock clutch letting go on dr's. What rpm did you launch @? I'm going to the track w 26" slicks tomorrow night and am wondering if I should try to launch @ all...
You bumped a 7 months old thread about a mustang on a GM forum to ask that?
Old 12-10-2010, 02:59 PM
  #30  
Teching In
 
Jonbones's Avatar
 
Join Date: Apr 2010
Posts: 0
Likes: 0
Received 0 Likes on 0 Posts
Default

Yep, I did. Thanks for the input.


So what rpm were you launching @ that you blew up the clutch?
Old 12-14-2010, 03:06 AM
  #31  
TECH Senior Member
iTrader: (18)
 
itsslow98's Avatar
 
Join Date: Apr 2006
Location: Maryland
Posts: 6,768
Likes: 0
Received 4 Likes on 4 Posts

Default

Originally Posted by Jonbones
Yep, I did. Thanks for the input.


So what rpm were you launching @ that you blew up the clutch?
9,000 is what i heard, they had to use a monster tach glued to the dash to see the rpms.



Quick Reply: 2011 mustang dyno and run numbers



All times are GMT -5. The time now is 08:17 PM.