Official Polk County thread!
What you building? I can get you a kit car pan with the pick up tube,gaskets,dipstick tube,windage tray and mounting hardware for 175..
It fits virtually all v8 rwd chevys from 1955 to 1995
Anyone need any automotive work done? I need to make some money so i can go racing .. late this week ill be done with all the cars in my shop so ill be ready for whatever. motor swaps,mods,suspension, air conditioning stuff, drivetrain, whatever
yes the truck pan wont fit unless if you have a aftermarket tubalar k member. Then the pan just hangs really low. Your best bet would be a f-body pan obvisouly i guess.
yes the truck pan wont fit unless if you have a aftermarket tubalar k member. Then the pan just hangs really low. Your best bet would be a f-body pan obvisouly i guess.
Last edited by BLINGOLE; Nov 4, 2011 at 09:50 AM.
I want to send some time and see if that kit car pan is any shorter then a f body pan. Im scared one day if my car came up in a big wheel stand it might hit the pan on the landing.
mike my trans needs to be rebuilt. got everything else working good. see if you can coordinate with wade for you pulling and re-installing the trans and him rebuilding it and give me a total figure. because now the car is driving beautifully, but I have no 3rd at all and still grinds 2nd. want to get this taken care of so i can get going on my truck. I need to order the 'cage for it next and start putting it in
On The Tree
Joined: Aug 2011
Posts: 131
Likes: 0
From: Lakeland, Fl
mike my trans needs to be rebuilt. got everything else working good. see if you can coordinate with wade for you pulling and re-installing the trans and him rebuilding it and give me a total figure. because now the car is driving beautifully, but I have no 3rd at all and still grinds 2nd. want to get this taken care of so i can get going on my truck. I need to order the 'cage for it next and start putting it in
the 68 in my sig. planning on going 9's, so I gotta put the monkey bars in. the frame has been sandblasted and painted, as well as the suspension. it's sitting as a rolling chassis right now. I gotta patch a hole in the cab floor then it will be ready to go on and get the cage built. I haven't worked on it in montch becasue I have been too busy with getting everything with the t/a right since it's my daily
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo truck should be around the 3100-3200 mark. as far as the 5.3 goes, I plan on just putting in a stock junkyard motor and boosting the hell out of it with the aid of a meth kit. if it blows, I just pick up another one. the motors are cheap, so worst case I'm out $500 for another one. that is, if it doesn't hold. looking at around 15 psi, 530-550 whp (it's a stick, so on't lose as much through drivetrain loss)
truck should be around the 3100-3200 mark. as far as the 5.3 goes, I plan on just putting in a stock junkyard motor and boosting the hell out of it with the aid of a meth kit. if it blows, I just pick up another one. the motors are cheap, so worst case I'm out $500 for another one. that is, if it doesn't hold. looking at around 15 psi, 530-550 whp (it's a stick, so on't lose as much through drivetrain loss)
also i'm picking up Mark's turbo off his rx7. it's a 76 mm, so it should be good for what I need
that's what I'm going to do if i get one that's disassembled. go ahead and put some hardware and head gaskets in, maybe a little cam, and see what it does. I have some catching up to do with a certain black firebird
also i'm picking up Mark's turbo off his rx7. it's a 76 mm, so it should be good for what I need
also i'm picking up Mark's turbo off his rx7. it's a 76 mm, so it should be good for what I need
Dragstrip thursday btw! Im putting my bmr drag bar in like a hour,,,
On The Tree
Joined: Aug 2011
Posts: 131
Likes: 0
From: Lakeland, Fl
Wow!! Just got back a little while ago from picking up the Camaro from BLINGOLE's shop. The header, ORY and catback install went great. This thing sounds great now! I can tell its got more pull to it too. Fantastic job Mike !!!
Hmmmmm, now we gotta start thinking heads, cam and stuff!
Hmmmmm, now we gotta start thinking heads, cam and stuff!
I just ordered qa1 coilover's! Hopefully I can get them on and get the car aligned by Thursday night for test and tune. Put my bmr drag bar on last night too! Wow what a diference that thing made,the car does not move side to side for **** now.
or bolts?
On The Tree
Joined: Aug 2011
Posts: 131
Likes: 0
From: Lakeland, Fl
