Meth injection??
#23
9 Second Club
iTrader: (37)
Im using AIS kit and pure meth.
Friday ambient was 68
My IAT started on the line at 82 degrees and ended at 77. That, to me, makes an a/w setup too much hassle since I am just a test and tuner. With a better i/c and air being picked up from some place besides behind my radiator, I think the temps would go lower.
Friday ambient was 68
My IAT started on the line at 82 degrees and ended at 77. That, to me, makes an a/w setup too much hassle since I am just a test and tuner. With a better i/c and air being picked up from some place besides behind my radiator, I think the temps would go lower.
#24
You can certanly run pure meth, or pure water, but 50/50 is safe, and it yeilds detonation protection equivalent to C16 race gas. Most people will not need more than that.
The spark blow out that the person mentioned is likely due to over-injection. And it is true that you can inject more volume with pure meth and that will spark blow-out not happen as easaly. Just be aware of the factors I listed above. What we recomend is a more correct injection volume with 50/50, which will eliminate that spark blow-out safely. The fact that they got spark blow-out was a warning that they were over-injecting a bit.
Not trying to scare people from a certain philosophy. There is certanly a lot to be said for high meth mixes. Just be aware of the fact that water does have a higher specific heat and 50/50 is very safe and efective.
#26
TECH Addict
iTrader: (8)
Join Date: Oct 2008
Location: toronto ontario canada
Posts: 2,047
Likes: 0
Received 2 Likes
on
2 Posts
Absolutely.
You can certanly run pure meth, or pure water, but 50/50 is safe, and it yeilds detonation protection equivalent to C16 race gas. Most people will not need more than that.
The spark blow out that the person mentioned is likely due to over-injection. And it is true that you can inject more volume with pure meth and that will spark blow-out not happen as easaly. Just be aware of the factors I listed above. What we recomend is a more correct injection volume with 50/50, which will eliminate that spark blow-out safely. The fact that they got spark blow-out was a warning that they were over-injecting a bit.
Not trying to scare people from a certain philosophy. There is certanly a lot to be said for high meth mixes. Just be aware of the fact that water does have a higher specific heat and 50/50 is very safe and efective.
You can certanly run pure meth, or pure water, but 50/50 is safe, and it yeilds detonation protection equivalent to C16 race gas. Most people will not need more than that.
The spark blow out that the person mentioned is likely due to over-injection. And it is true that you can inject more volume with pure meth and that will spark blow-out not happen as easaly. Just be aware of the factors I listed above. What we recomend is a more correct injection volume with 50/50, which will eliminate that spark blow-out safely. The fact that they got spark blow-out was a warning that they were over-injecting a bit.
Not trying to scare people from a certain philosophy. There is certanly a lot to be said for high meth mixes. Just be aware of the fact that water does have a higher specific heat and 50/50 is very safe and efective.
would i see any benefits of meth injection on my 8.6:1 motor running around 20 psi ? i know i can run 20 psi safely on 94 octane but will meth cool the air charge further and give me more power ?
#28
For instance, if your IATs are really high, you may get a power gain without a retune just from the cooling effect. I had one customer with a 2V Mustang and a KB blower that picked up 24WHP on a 400WHP car (Mustang Dyno) just from the cooling. This is because that blower in AZ heat was making seriously high IATs.
But usually the big power comes from the tune. With the octane and cooling provided, a bit more boost and a bit more timing will likely make a big difference in power.
What sort of timing, AFR, and power are we looking at here?