891 RWHP with Vortech & LTX
#22
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
You will need to mill the back of the pulley. When you pull yours off you will see what I am talking about. Its as simple as milling .030" off the back on a radius table that way it can center it self on the ati dampener.
#23
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
Only time will tell. I am waiting on some IC 1000 injectors. Then back on the dyno.
#32
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
I am very impressed with the power level and cant wait for my 1000cc injectors to show up so we can turn the boost up.
Last edited by YSILT1; 06-23-2011 at 10:27 AM.
#33
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
#34
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
The only other thing is what kid of gain if any do you think I would see switching to an 1 7/8 header and maybe the new dual 3" exhaust from Kooks.
Last time we were on the dyno and I tried opening the cutout on the Borla and got the same power. So these #'s were with the Borla shut and all going out the one side.
#35
Launching!
iTrader: (5)
Join Date: Aug 2005
Location: new mexico
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
Thanks. Its cool seeing this starting to make the HP I wanted. I was doubting and thinking I should have switch to an LS years ago.
The only other thing is what kid of gain if any do you think I would see switching to an 1 7/8 header and maybe the new dual 3" exhaust from Kooks.
Last time we were on the dyno and I tried opening the cutout on the Borla and got the same power. So these #'s were with the Borla shut and all going out the one side.
The only other thing is what kid of gain if any do you think I would see switching to an 1 7/8 header and maybe the new dual 3" exhaust from Kooks.
Last time we were on the dyno and I tried opening the cutout on the Borla and got the same power. So these #'s were with the Borla shut and all going out the one side.
#36
TECH Fanatic
iTrader: (32)
Do you know if I can get away with using the same belt with the 80 tooth crank pulley? I have two of them and don't want to buy a longer one if I don't need to.
#37
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
So I just dynoed with my 80 T Crank Pulley and ATI dampener.
We ran out of fuel. So I know there is at least 950 RWHP in it. This is also with NO METH still. Maybe has 4 digits in it. With meth.
Only time will tell. Here is the dyno of 891 RWHP that we did today. Will be getting some new injectors tomorrow. Also, I think I am almost at the end of my twin 255lph pumps too.
We ran out of fuel. So I know there is at least 950 RWHP in it. This is also with NO METH still. Maybe has 4 digits in it. With meth.
Only time will tell. Here is the dyno of 891 RWHP that we did today. Will be getting some new injectors tomorrow. Also, I think I am almost at the end of my twin 255lph pumps too.
#38
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
Also this proto type intercooler from Vortech works amazing. With running ice in the tank. Intake air temps were from 65 degrees F to 86 degrees at full throttle. The ambient temp in the dyno was over 90 degrees.
#40
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
Thanks. This is also with the 1 3/4 Pacesetter headers and single 3" Borla running all through the muffler. I tried opening the cut out and saw no gain. Not sure if larger headers and dual 3" exhaust will help.
Talked with Kooks and they would need to have the car to custom make 2" primary headers and a 3" dual exhaust. Just not sure if the gains are worth the 5K plus the quoted me to make it one off.
Talked with Kooks and they would need to have the car to custom make 2" primary headers and a 3" dual exhaust. Just not sure if the gains are worth the 5K plus the quoted me to make it one off.