891 RWHP with Vortech & LTX
#62
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
The 891 was with 17 lbs of boost.
#63
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Here are a few videos.
These are from the previous 740 RWHP runs. These were shot with my Android.
http://s777.photobucket.com/albums/y...7-17-55_85.mp4
http://s777.photobucket.com/albums/y...-24-16_173.mp4
This one is from the 891 run. A friend of mine shot this off his I Phone.
http://s777.photobucket.com/albums/y...t=IMG_0230.mp4
These are from the previous 740 RWHP runs. These were shot with my Android.
http://s777.photobucket.com/albums/y...7-17-55_85.mp4
http://s777.photobucket.com/albums/y...-24-16_173.mp4
This one is from the 891 run. A friend of mine shot this off his I Phone.
http://s777.photobucket.com/albums/y...t=IMG_0230.mp4
#70
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
That is a very sano setup and some excellent numbers. All in a great-looking car, too. I think the 1 7/8" headers are worth the investment but don't believe going to 2" would be worth more than about 15-20rwhp above 5500rpm. IMO a dual 3" system will pay off a lot more, all through the powerband, than the 2" headers.
Can you share your cam specs? I'm doing a similar SBC (and sticking with 1 7/8", true duals for similar rea$on$).
Jim
Can you share your cam specs? I'm doing a similar SBC (and sticking with 1 7/8", true duals for similar rea$on$).
Jim
Last edited by DeltaT; 08-29-2011 at 12:47 PM. Reason: fixed typo 'above 5500rpm'
#71
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
That is a very sano setup and some excellent numbers. All in a great-looking car, too. I think the 1 7/8" headers are worth the investment but don't believe going to 2" would be worth more than about 15-20rwhp about 5500rpm. IMO a dual 3" system will pay off a lot more, all through the powerband, than the 2" headers.
Can you share your cam specs? I'm doing a similar SBC (and sticking with 1 7/8", true duals for similar rea$on$).
Jim
Can you share your cam specs? I'm doing a similar SBC (and sticking with 1 7/8", true duals for similar rea$on$).
Jim
The cam is actually an Ultra Dyne. My bad. But here are the specs.
Duration @ .050 255 I and 263 E. Lift is .626 I and .626 E on a 114 solid roller. I am using comp 888-16 solid lifters. Chad @ Golen Engines speced this out for me.
I think I am going to try doing the 3" dual exhaust first then switch out headers. I think I am going to just make one with Borla mufflers. I like the Kooks, but I could make it for way less and have better mufflers and tips on it.
Looking at the graph were it starts to flaten out since the AFR was going up to 12.8 :1 . I think the car will peak out at 925 to 930 with enough fuel. I was going to do one bandaid run with the meth on, but Mark @ RMCR didnt want to push it since the injectors were at 100% duty cycle by 4800 RPM.
I am glad he is always there to talk so since into me.
![Nod](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_nod.gif)
#72
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
The intercooler and all the priping is 3".
Headers are the cheap Pacesetter 1 3/4 Long tubes with a Single 3" Brla Exhaust with the cutout plate closed and all going through the muffler.
Turbo Size????? This is a Vortech YSi Supercharger
![Nod](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_nod.gif)
#73
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
To be honest with out the LS pcm conversion I did this would of never been possible. Unless I used a FAST or Bigstuff.
#74
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Sure thing.
The cam is actually an Ultra Dyne. My bad. But here are the specs.
Duration @ .050 255 I and 263 E. Lift is .626 I and .626 E on a 114 solid roller. I am using comp 888-16 solid lifters. Chad @ Golen Engines speced this out for me.
I think I am going to try doing the 3" dual exhaust first then switch out headers. I think I am going to just make one with Borla mufflers. I like the Kooks, but I could make it for way less and have better mufflers and tips on it.
Looking at the graph were it starts to flaten out since the AFR was going up to 12.8 :1 . I think the car will peak out at 925 to 930 with enough fuel. I was going to do one bandaid run with the meth on, but Mark @ RMCR didnt want to push it since the injectors were at 100% duty cycle by 4800 RPM.
I am glad he is always there to talk so since into me.![Nod](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_nod.gif)
The cam is actually an Ultra Dyne. My bad. But here are the specs.
Duration @ .050 255 I and 263 E. Lift is .626 I and .626 E on a 114 solid roller. I am using comp 888-16 solid lifters. Chad @ Golen Engines speced this out for me.
I think I am going to try doing the 3" dual exhaust first then switch out headers. I think I am going to just make one with Borla mufflers. I like the Kooks, but I could make it for way less and have better mufflers and tips on it.
Looking at the graph were it starts to flaten out since the AFR was going up to 12.8 :1 . I think the car will peak out at 925 to 930 with enough fuel. I was going to do one bandaid run with the meth on, but Mark @ RMCR didnt want to push it since the injectors were at 100% duty cycle by 4800 RPM.
I am glad he is always there to talk so since into me.
![Nod](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_nod.gif)
How does yours idle?
You guys were wise to stop testing when you did. Running out of injector under boost is a recipe for disaster when tuning.
Your wiring picture brings back memories! And I'm going to re-live it this winter when I switch over to my new efi system.
Jim
#75
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Cool, thanks for sharing the specs. The cam I had made up is pretty similar, a Comp solid roller with one of their .420" intake lobes and one of their .406" exhaust lobes - 256/268@.050" on a 115lsa, net lift .692"/.707". I am using the same lifters but with a .180" offset intake lifter. 421" SBC/YSi combo.
How does yours idle?
You guys were wise to stop testing when you did. Running out of injector under boost is a recipe for disaster when tuning.
Your wiring picture brings back memories! And I'm going to re-live it this winter when I switch over to my new efi system.
Jim
How does yours idle?
You guys were wise to stop testing when you did. Running out of injector under boost is a recipe for disaster when tuning.
Your wiring picture brings back memories! And I'm going to re-live it this winter when I switch over to my new efi system.
Jim
Ya the wiring wasn't as bad as it looks. I am so glad I did it myself though. That way I could clean the harness up and cut everything to length. By far one of the best mods.
This car is very street able I drove it all last week to and from work.
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
Also Golen was right we have checked the lash on the rockers and with good components they dont really come out of adjustment. Going to make it a once a year check now.
#77
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
So I got my injectors in. IC 1000's from FIC. These should get the job done. Only bummer is the car is still @ the body shop getting a few scatches fixed and painting a Trans Am hatch for it. Plus side it should look way better with the Trans Am wing.
Here are some shots of the injectors since I cant put them in. Should have dyno results and a 900 RWHP plus # very soon.![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
![](https://ls1tech.com/forums/picture.php?albumid=9961&pictureid=76685)
Here are some shots of the injectors since I cant put them in. Should have dyno results and a 900 RWHP plus # very soon.
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
#79
Launching!
Thread Starter
iTrader: (6)
Join Date: Oct 2007
Location: Colorado Springs
Posts: 266
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Thanks.
I have been way to busy at the shop to do anything on it. I have the injectors and I am thinking of doing Kooks headers and there 3" dual exhaust. Would love to see it break 4 digits.
Honestly, I am just not sure what the exhaust will gain me. Is it worth the 3K. I will order it in January and only time will tell.
I think it will be around 925rwhp with the injectors. I will try and throw it back on the dyno maybe next week.
I have been way to busy at the shop to do anything on it. I have the injectors and I am thinking of doing Kooks headers and there 3" dual exhaust. Would love to see it break 4 digits.
Honestly, I am just not sure what the exhaust will gain me. Is it worth the 3K. I will order it in January and only time will tell.
I think it will be around 925rwhp with the injectors. I will try and throw it back on the dyno maybe next week.
#80
8 Second Club
iTrader: (9)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Thanks.
I have been way to busy at the shop to do anything on it. I have the injectors and I am thinking of doing Kooks headers and there 3" dual exhaust. Would love to see it break 4 digits.
Honestly, I am just not sure what the exhaust will gain me. Is it worth the 3K. I will order it in January and only time will tell.
I think it will be around 925rwhp with the injectors. I will try and throw it back on the dyno maybe next week.
I have been way to busy at the shop to do anything on it. I have the injectors and I am thinking of doing Kooks headers and there 3" dual exhaust. Would love to see it break 4 digits.
Honestly, I am just not sure what the exhaust will gain me. Is it worth the 3K. I will order it in January and only time will tell.
I think it will be around 925rwhp with the injectors. I will try and throw it back on the dyno maybe next week.
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)