Phamspeed Turbo install part TWO,
Thread Starter
TECH Senior Member
iTrader: (16)
Joined: Oct 2002
Posts: 6,907
Likes: 6
From: Albuquerque, NM
OK OK I'll start it....soon
Had to finish the passenger IC routing today...had a rain delay for a few but got it all up...now its time to wait for the rest of my HTS clamps....ordered too few the first time around
SO other than the alternator bracket and a few clamps to the tranny lines...and moving my ADJ FPR...(rain held that off) boost controller and some vac lines to route...she'll be ready.
Here is the routing from the GT42 to the inlet of the FMIC, a pic with the plastic splash guard, and a pic of it off. I was able to keep both splash guards down there which is awesome. The IC routing goes right behind the air dam and sits about 2 inches from the bottom of the air dam....about the same as my ATI kit so no worries there.
Heres the rest including some pics of my HTS clamps and silicone....coolness
Thanks JIM@HTS you and your products have helped me complete my project with excellent looking results and I know they'll handle the boost very nicely.
J
Had to finish the passenger IC routing today...had a rain delay for a few but got it all up...now its time to wait for the rest of my HTS clamps....ordered too few the first time around
SO other than the alternator bracket and a few clamps to the tranny lines...and moving my ADJ FPR...(rain held that off) boost controller and some vac lines to route...she'll be ready.
Here is the routing from the GT42 to the inlet of the FMIC, a pic with the plastic splash guard, and a pic of it off. I was able to keep both splash guards down there which is awesome. The IC routing goes right behind the air dam and sits about 2 inches from the bottom of the air dam....about the same as my ATI kit so no worries there.
Heres the rest including some pics of my HTS clamps and silicone....coolness
Thanks JIM@HTS you and your products have helped me complete my project with excellent looking results and I know they'll handle the boost very nicely.
J
Last edited by frcefed98; May 5, 2005 at 10:20 PM.
Originally Posted by frcefed98
OK OK I'll start it....soon
Had to finish the passenger IC routing today...had a rain delay for a few but got it all up...now its time to wait for the rest of my HTS clamps....ordered too few the first time around
SO other than the alternator bracket and a few clamps to the tranny lines...and moving my ADJ FPR...(rain held that off) boost controller and some vac lines to route...she'll be ready.
Here is the routing from the GT42 to the inlet of the FMIC one with the plastic cover one and one of it off. I was able to keep both splash guards down there which is awesome. The IC routing goes right behind the air dam and sits about 2 inches from the bottom of the air dam....about the same as my ATI kit so no worries there.
Thanks JIM@HTS you and your products have helped me complete my project with excellent looking results and I know they'll handle the boost very nicely.
J
Had to finish the passenger IC routing today...had a rain delay for a few but got it all up...now its time to wait for the rest of my HTS clamps....ordered too few the first time around
SO other than the alternator bracket and a few clamps to the tranny lines...and moving my ADJ FPR...(rain held that off) boost controller and some vac lines to route...she'll be ready.
Here is the routing from the GT42 to the inlet of the FMIC one with the plastic cover one and one of it off. I was able to keep both splash guards down there which is awesome. The IC routing goes right behind the air dam and sits about 2 inches from the bottom of the air dam....about the same as my ATI kit so no worries there.
Thanks JIM@HTS you and your products have helped me complete my project with excellent looking results and I know they'll handle the boost very nicely.
J
ha ha Any word on the alt bracket?? U call them and ask yet??
Kyle
Thread Starter
TECH Senior Member
iTrader: (16)
Joined: Oct 2002
Posts: 6,907
Likes: 6
From: Albuquerque, NM
Haa haa we posted at the same time almost. Yep John@phamspeed is on top of it, the alternator bracket was sent out to be finished up and will be over nighted back to him and off to me...it'll be here very soon
J
J
Originally Posted by frcefed98
Haa haa we posted at the same time almost. Yep John@phamspeed is on top of it, the alternator bracket was sent out to be finished up and will be over nighted back to him and off to me...it'll be here very soon
J
J
Awsome so were talking about weds.??????? so tuning will be done by friday and at the track on fri, or sat.....
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
On The Tree
Joined: Dec 2002
Posts: 181
Likes: 0
From: Land of no Drag Strip
Everything looks real good from what I can see. Wish I could have helped out, but have been real busy at work and at home. Just so you know the PNYKILR is no more. Urist Racing is buying the car and slapping a big old turbo on it. big thumper 101mm. I guess they wanted a 7 second LT1 TA. You know how those Mustang Outlaw guy's are.
I'll try and make it up there tomorrow.
Neal
I'll try and make it up there tomorrow.
Neal
Thread Starter
TECH Senior Member
iTrader: (16)
Joined: Oct 2002
Posts: 6,907
Likes: 6
From: Albuquerque, NM
Neal you'll always be PNYKILR...I'll let you borrow mine....gotta have some one in the driver seat that isn't afraid to keep his foot in it....
Man I don't know what to say....glad Urist is buying it can't wait to see it.
Kyle I'll try to keep it to two weeks now...gots to get it emissioned.
J
Man I don't know what to say....glad Urist is buying it can't wait to see it.
Kyle I'll try to keep it to two weeks now...gots to get it emissioned.
J
Thread Starter
TECH Senior Member
iTrader: (16)
Joined: Oct 2002
Posts: 6,907
Likes: 6
From: Albuquerque, NM
That isn't good, Time to do the ol rebuild huh? Maybe you'll get away with just a new crush collar and new bearings....like I did the last time mine started whining....ET streets and Drags don't help the ol 10 bolt
J
Looking real good Jer!!! You reallly took your time and did everything right on this install so it should payoff for you big time.. After all the parts you ordered did you ever think that a alternater bracket would of held you up.. I need the same thing and it seems like tring to find a piece of gold or something 
Well I can't wait to you fire this thing up and get rolling!!!!!
I need the same thing and it seems like tring to find a piece of gold or something Well I can't wait to you fire this thing up and get rolling!!!!! 
Thread Starter
TECH Senior Member
iTrader: (16)
Joined: Oct 2002
Posts: 6,907
Likes: 6
From: Albuquerque, NM
Thanks Pat, yeah its kinda ironic that the bracket is the hold up, but it really wasn't needed until now I'm glad I was able to take my time on it. I think it came out a lot better had I tried to do it right away.
WS-Sick
Thanks, yep I'm working on the car on my own after I get out of work on the weekdays. I have the weekend off, but I have to watch my 2 year old son cuz momma works on the weekends....so its kinda drug out. Every now and then I do get some help from my Dad, brother or my buddy Frank...they've all helped as much as they can. Its my first turbo set up, and my first time setting actually messing with anything turbocharged....its been real fun. But this is my 3rd FI set up. I owned 2 supercharger set ups before the turbo.
J
I'm glad I was able to take my time on it. I think it came out a lot better had I tried to do it right away. WS-Sick
Thanks, yep I'm working on the car on my own after I get out of work on the weekdays. I have the weekend off, but I have to watch my 2 year old son cuz momma works on the weekends....so its kinda drug out. Every now and then I do get some help from my Dad, brother or my buddy Frank...they've all helped as much as they can. Its my first turbo set up, and my first time setting actually messing with anything turbocharged....its been real fun. But this is my 3rd FI set up. I owned 2 supercharger set ups before the turbo.
J
