STS Firehawk Install Thread
Thread Starter
Banned
iTrader: (2)
Joined: Jun 2008
Posts: 173
Likes: 0
From: ERAU. Daytona Beach, FL
I havent hooked up any boost to the motor.... so the maf is clean...
and right now it has one of those mail order tunes from the guy that owned it before me for the CAGS and 4.11's and stuff
and right now it has one of those mail order tunes from the guy that owned it before me for the CAGS and 4.11's and stuff
Thread Starter
Banned
iTrader: (2)
Joined: Jun 2008
Posts: 173
Likes: 0
From: ERAU. Daytona Beach, FL
Well i got some exhasut on it today... just a 90 bend and then a LM1. my main thing was to get it not pointing at my nittos. It sounds great i think... Ill post a cound clip prob tomorrow. but it needs to get cleaned up later.
Im still confused on how to hook up my bov. boost controller and boost gauge into the vacum lines...
I had my boost/vac gauge hook up and it was reading 20mm/hg at all rpms.... and then i started it later that day and it was at 4 and now its at 0... so idk. but thats only one that i found a spot to tap in... I still need to hook up 2 more..
and that one isnt even working... so i need help
Other than that... i should be good.
just waiting on a new Keeper from patriot to finish the springs
then i need to run the wires to the waste gate... easy
ill put the injectors in at norris..
I was about to call and set up a new appointment with Mike Norris... but
i think my friggin clutch is slippin now.
Im still confused on how to hook up my bov. boost controller and boost gauge into the vacum lines...
I had my boost/vac gauge hook up and it was reading 20mm/hg at all rpms.... and then i started it later that day and it was at 4 and now its at 0... so idk. but thats only one that i found a spot to tap in... I still need to hook up 2 more..
and that one isnt even working... so i need help
Other than that... i should be good.
just waiting on a new Keeper from patriot to finish the springs
then i need to run the wires to the waste gate... easy
ill put the injectors in at norris..
I was about to call and set up a new appointment with Mike Norris... but
i think my friggin clutch is slippin now.
Thread Starter
Banned
iTrader: (2)
Joined: Jun 2008
Posts: 173
Likes: 0
From: ERAU. Daytona Beach, FL
Got everything done. except the last valve spring. the injectors. and im trying to figure out the clutch. but im not going to mike norris anymore.
CAUSE I JUST BOUGHT HP TUNERS..!!!! Kinda exciting.. kinda scared.
CAUSE I JUST BOUGHT HP TUNERS..!!!! Kinda exciting.. kinda scared.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
