Need a 42# table
02-23-2006, 11:00 PM
#1
10 Second Club
Thread Starter
iTrader: (9)
Join Date: Jun 2003
Location: Goshen, IN
Posts: 1,001
Likes: 0
Received 0 Likes
on
0 Posts
Need a 42# table Does anyone have a table for the 42# Lucas/Dephi injectors?
I am nervous about simply scaling the table as I believe the disk injectors have different response characteristics than the current pintle injectors.
As an aside, I was astounded today when I finally got a log with the 370 inch motor and my 30# SVOs saturated at 4500 at 12.5:1 and it went as lean as 15:1. Luckily nothing broke ...
I am nervous about simply scaling the table as I believe the disk injectors have different response characteristics than the current pintle injectors.
As an aside, I was astounded today when I finally got a log with the 370 inch motor and my 30# SVOs saturated at 4500 at 12.5:1 and it went as lean as 15:1. Luckily nothing broke ...
02-23-2006, 11:17 PM
#2
Flossin' twin turbos
iTrader: (55)
Join Date: Jun 2004
Location: Chicago
Posts: 3,148
Likes: 0
Received 0 Likes
on
0 Posts
48.83314694 49.13748993 49.43995947 49.74058975 50.03941391 50.33646413 50.63177161 50.92536669 51.21727881 51.50753658 51.79616782 52.08319956 52.36865812 52.65256906 52.93495731 53.21584708 53.49526201
Last edited by Moparnos (The SLP Guy); 02-28-2006 at 12:02 PM.
02-26-2006, 09:09 PM
#4
12 Second Club
iTrader: (1)
Join Date: Apr 2004
Location: Clarksville, TN
Posts: 1,369
Likes: 0
Received 0 Likes
on
0 Posts
I used that table for mine earlier today... no dice.
Got idle alright, but when I try to give it gas it gets WAY lean and sputters out...
Anything I should go look for?
Got idle alright, but when I try to give it gas it gets WAY lean and sputters out...
Anything I should go look for?
02-26-2006, 09:56 PM
#6
12 Second Club
iTrader: (1)
Join Date: Apr 2004
Location: Clarksville, TN
Posts: 1,369
Likes: 0
Received 0 Likes
on
0 Posts
ok, so I went back and took out some of the other stuff that I had done but left the injector table alone.
Looks like that took care of my problem, that injector table looks good from my end!
Looks like that took care of my problem, that injector table looks good from my end!
02-26-2006, 10:29 PM
#7
Flossin' twin turbos
iTrader: (55)
Join Date: Jun 2004
Location: Chicago
Posts: 3,148
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by CamTom12
I used that table for mine earlier today... no dice.
Got idle alright, but when I try to give it gas it gets WAY lean and sputters out...
Anything I should go look for?
Got idle alright, but when I try to give it gas it gets WAY lean and sputters out...
Anything I should go look for?
Trending Topics
02-28-2006, 11:59 AM
#10
Flossin' twin turbos
iTrader: (55)
Join Date: Jun 2004
Location: Chicago
Posts: 3,148
Likes: 0
Received 0 Likes
on
0 Posts
Part Number Delphi 01D030B (Lucas old 5208009, Lucas New 621031, Delphi old D3181AA)
Static Flow Rate: 42.29 lb/hr @ 43.5PSI (300kPa) or 320gm/min
==========48.83314694 49.13748993 49.43995947 49.74058975 50.03941391 50.33646413 50.63177161 50.92536669 51.21727881 51.50753658 51.79616782 52.08319956 52.36865812 52.65256906 52.93495731 53.21584708 53.49526201
Static Flow Rate: 42.29 lb/hr @ 43.5PSI (300kPa) or 320gm/min
==========48.83314694 49.13748993 49.43995947 49.74058975 50.03941391 50.33646413 50.63177161 50.92536669 51.21727881 51.50753658 51.79616782 52.08319956 52.36865812 52.65256906 52.93495731 53.21584708 53.49526201
02-28-2006, 05:28 PM
#13
TECH Resident
iTrader: (94)
Join Date: May 2003
Location: port st lucie florida
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
ok I think I changed the right one is it under fuel control- flow rate vs. kpa. Then copied and pasted the above values into the slots . Is that correct?
03-01-2006, 12:32 PM
#18
Coal Mining Director
iTrader: (17)
Join Date: Nov 2001
Location: Virginia
Posts: 4,442
Likes: 0
Received 0 Likes
on
0 Posts
Just curious....if the fuel pressure is stable , why isn't the number constant after it's converted for the proper pressure? Like 48.50? What's the factory constant for factory injectors?
