My 8.8 build (pics added, rearend finished)
#1
Launching!
Thread Starter
iTrader: (24)
Join Date: May 2008
Location: Boone Iowa
Posts: 265
Likes: 0
Received 0 Likes
on
0 Posts
My 8.8 build (pics added, rearend finished)
This is my 8.8 build started with explorer rearend, narrowed. im - 4 Inches both sides. doing wolfe race craft mini tubs. 4.30 gears , 31 spline axles, 31 spline locker.plan on running 275 60 15 mt drag radials.
Last edited by cantfind2nd; 06-05-2011 at 07:32 PM. Reason: pics added
#7
12 Second Club
Join Date: Feb 2006
Location: Catlettsburg, Ky
Posts: 876
Likes: 0
Received 0 Likes
on
0 Posts
Looks good I see you put fbody brackets on 8.8 tubes instead of retubing the 8.8 center section with 10bolt tubes.
I wish you the best of luck with your torque arm setup. Few people seems to have any luck with welding on the cast center section.
I wish you the best of luck with your torque arm setup. Few people seems to have any luck with welding on the cast center section.
Trending Topics
#8
Launching!
Thread Starter
iTrader: (24)
Join Date: May 2008
Location: Boone Iowa
Posts: 265
Likes: 0
Received 0 Likes
on
0 Posts
its been fitted in car and mocked up, waiting on parts to set up gears.think the reason they had bad luck is they only welded to the cast center... and didnt make a brace going back to the mild steal axle tube. you can weld to the center its cast steal not cast iron, i preheated center with a torch and just welded it. i beat on another test housing with a 3 pound hammer and coudnt break the welds....
Last edited by cantfind2nd; 05-26-2011 at 08:11 PM. Reason: mis spell
#13
TECH Resident
Join Date: Dec 2001
Location: Mehlingen, Germany
Posts: 937
Likes: 0
Received 0 Likes
on
0 Posts
its been fitted in car and mocked up, waiting on parts to set up gears.think the reason they had bad luck is they only welded to the cast center... and didnt make a brace going back to the mild steal axle tube. you can weld to the center its cast steal not cast iron, i preheated center with a torch and just welded it. i beat on another test housing with a 3 pound hammer and coudnt break the welds....
Have you seen the solution Griggs racing has for a torque arm?
#14
Launching!
Thread Starter
iTrader: (24)
Join Date: May 2008
Location: Boone Iowa
Posts: 265
Likes: 0
Received 0 Likes
on
0 Posts
its cast steal, CAT certified welder at work says it is cast steal, do some more reading youll find its not cast iron.... that torque arm set up wont work on a 8.8 from an explorer. all those are for fox body mustangs. nice set up though.
#17
its been fitted in car and mocked up, waiting on parts to set up gears.think the reason they had bad luck is they only welded to the cast center... and didnt make a brace going back to the mild steal axle tube. you can weld to the center its cast steal not cast iron, i preheated center with a torch and just welded it. i beat on another test housing with a 3 pound hammer and coudnt break the welds....
https://ls1tech.com/forums/gears-axl...8-project.html
#18
Launching!
Thread Starter
iTrader: (24)
Join Date: May 2008
Location: Boone Iowa
Posts: 265
Likes: 0
Received 0 Likes
on
0 Posts
Its some kind of cast steal i promise. i took it to our caterpillar certified welders at work.ive had them weld several 8.8s in mustangs. they preheat it and just mig it. the guy who did it has been welding 30 + years for us.look around online... i repeat they are not cast iron. they say cast iron will pop, crack and explode when trying to mig weld it. this is some kind of cast steal alloy.
#19
Its some kind of cast steal i promise. i took it to our caterpillar certified welders at work.ive had them weld several 8.8s in mustangs. they preheat it and just mig it. the guy who did it has been welding 30 + years for us.look around online... i repeat they are not cast iron. they say cast iron will pop, crack and explode when trying to mig weld it. this is some kind of cast steal alloy.