AlexLs1

iTrader: (1)

Where is the cheapest place or company that has the best prices. That are built direct bolt in, with in reason. I also want to keep my traction control and ABS. Picky I know. I'am sick of this damn 10 bolt.
Anyone whose selling there aftermarket rearend used, PM me.

Thanks in advance for any input.

-Alex.

Jays00ss

iTrader: (1)

PM sent. Great place to buy!!!!

66 BADBOY

iTrader: (2)

Maybe try Drive Train Specialists in Michigan? I toured their place in September. Really nice and knowledgable guys. Not sure if they are into the F-body stuff though. I am going with them for a Dana 60 in my 66 Nova. Maybe it be worth a call for you.

AlexLs1

iTrader: (1)

Thanks for the input guys.

ssvert99

iTrader: (26)

new style fabricated 9 inch rearends here.
fabricated housing, (built in relocators, drain plug, stock anti-sway mounts all at no extra cost), Strange or Moser iron center section with posi and choice of gear, 31-35 spline axles, tunnel or trans xmember mounted torque arm, xmember for application with 4 hole adjustable t/a link. all parts powdercoated... 2500.00

several options available... chromemoly housing, 3 or 4 channel abs, aluminum case, spool or locker, housing brace, driveshaft, race anti-roll, etc.

this rearend with the aluminum case is lighter than the stock 10 bolt and much, much stronger.

best deal on the best rearend.

BlackScreaminMachine

iTrader: (17)

No 12 bolt is a direct bolt in, unless you send them your caliper brackets, i.e. Moser, if you can get a set and send to them, they will assemble the entire unit.

AlexLs1

iTrader: (1)

Thanks for the input guys, been a while since I looked back at this thread. I have some good leads and will be doing some more homework. Thanks for pointing me in the right direction.

EPP

iTrader: (22)

Free shipping, always. Bob
http://www.exoticperformanceplus.com....html?item=145

Jawsgear

iTrader: (2)

Check out our website. Free shipping too. Add LS1tech to comment section when you order.

Thanks, Jeff

382ssz28

iTrader: (24)

Talk to Adam or Mike at DTS. Great service and fair prices. There are no good deals. They are just plain exspensive. I will say my Dana60 was 200.00 less than a 12 bolt, but heavier. Pros-cons.

donkey mule

Customer service is a big plus when buying a rear end. Just read the horror stories when something goes wrong with a brand new rear end. I watched to see how sponsors responded when something went wrong. Saving $50 isnt worth it when problems happen and customer service stinks! Most of the sponsors are going to be close with the bottom line after shipping and options and such. I went with Bob over at EPP and had great customer service.

EPP

iTrader: (22)

Thanks, I appreciate it! Bob

bad2000z

iTrader: (4)

I went with Bob too! Very happy so far. SJM has good prices on Strange 12 bolts, but I didn't want to deal with sending in my backing plates/caliper brackets.

EPP

iTrader: (22)

Thanks! Bob

Jawsgear

iTrader: (2)

Some people might be new to this board but does not mean that customer service is 2nd rate. Keep that in mind.

Thanks, Jeff

Joey@Tick

iTrader: (20)

Shoot me a PM for best Moser pricing - with Free Shipping, of course.

bad2000z

iTrader: (4)

Very true. I had crappy luck with another driveline sponsor recently, so I went with EPP the second time around and couldn't be happier. Welcome to the board!

EPP

iTrader: (22)

Thanks for going with us, we're located close to Moser which helps out at times. Bob

yak

iTrader: (15)

I got my case and axels from bob at epp, and found a used center section on here. worked out nicely

EPP

iTrader: (22)

Thanks, the $1,000.00 housing and axle package shipped is hard to beat. Bob