welcome back, car! 
Its back!!!!
Thread Starter
On The Tree
Joined: Feb 2004
Posts: 107
Likes: 0
From: STL
Its back!!!! Well after two years of down time, and countless hours of problems and changing my mind on what to do with it. I got fed up and took it to a shop and gave it to them 1 week and some minor set backs I picked it back up today. I really missed the car and now cannot for the life of me wipe the smile off my face. Now all I need is a clutch and rear end.
Just out of curiosity has there been anyone on here running a stock clutch with a car that made good power?
Thanks
Mike.
Just out of curiosity has there been anyone on here running a stock clutch with a car that made good power?
Thanks
Mike.
Thread Starter
On The Tree
Joined: Feb 2004
Posts: 107
Likes: 0
From: STL
I know I need a clutch, I have always been affraid of it after modding it. Before it was just bolt ons. I am going to order a LS7 clutch for it. I just wanted it running, I also need to get a tune.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo Thread Starter
On The Tree
Joined: Feb 2004
Posts: 107
Likes: 0
From: STL
853 heads Ported, polished and milled(they were cheap....really cheap so I had to buy them. Plus I wanted to build on a budget), 918 springs, titainium retainers, LS6 intake, LS6 timing chain, SLP oil pump, High flow water pump, 160 thermostat, Comp lifters, 222/224 .561 112 lsa, Comp hardened push rods, Speed inc tensioner, Powerbond Underdrive pulley, Pacesetter long tubes, TS&P true duals I am sure there is something I left out.
But, like I said this project had to be put on the back burner for awhile, bought a house and wanted to be sure I can still have money to actually enjoy other stuff. Well, any missed it alot.
But, like I said this project had to be put on the back burner for awhile, bought a house and wanted to be sure I can still have money to actually enjoy other stuff. Well, any missed it alot.
Thread Starter
On The Tree
Joined: Feb 2004
Posts: 107
Likes: 0
From: STL
nothing special, just idleing Hopefully this works. http://www.youtube.com/watch?v=D6U2ASaYK20
still has an exhaust leak somewhere I just need to get it up in the air and track it down. Other than that and the bad belt tensioner pulley(fixed for now with a pulley out of the junk yard) sounds good I think. Let me know what you think of it.
still has an exhaust leak somewhere I just need to get it up in the air and track it down. Other than that and the bad belt tensioner pulley(fixed for now with a pulley out of the junk yard) sounds good I think. Let me know what you think of it.
Last edited by SLO POK 98; Mar 22, 2009 at 06:31 PM. Reason: more stuff