TORCHD 02 TA

iTrader: (39)

Does it matter the order on how you wire it to the prongs?

ruquick02ls1

Nice right write. Got one question does it make the SES light come on?

Thanks

TORCHD 02 TA

iTrader: (39)

The SES light does not come on b/c you are tapping into the OEM wiring for the fans. I know tha when Brian2006 did the fan mod his SES light came in, but he wired it differently, added a resistor and was good to go

TORCHD 02 TA

iTrader: (39)

just got me LEDs and switch today. holly hell that swith is big

Big Bird WS6

iTrader: (9)

so when the computer turns on the fan your light turns on? bad ***. i might do that

TORCHD 02 TA

iTrader: (39)

That is correct. You are tapped into the same pin from the harness.

I will be installing mine in the spring time

Nitehawk

I am wondering if a person could set this up with two switchs. I was thinking that i could get two new switchs that would fit in the same place as the fog light switch and traction control switch.

DaddySS

Nice write up, thanks.

TORCHD 02 TA

iTrader: (39)

here is mine installed

Jeff Smith

iTrader: (44)

I searched many posts here. Some of those posts I do not like relating to fan switch control..Finally I found this one excellent write-up..
Thanks!!!!

Topless TA

iTrader: (10)

VERY SLICK my friend, best switch panel i have seen

topdj-com

excellent,, so what was the mod to prevent the SES light?

TORCHD 02 TA

iTrader: (39)

Only time I get an CEL, is for some reason when I go to the track. my fans alway trip the CEL light LOL.. Dunno why

I need to put a resistor in mine.. My damn LEDs are soooooooo bright

96silverram

iTrader: (12)

Very nice write-up! I am actually looking for this exact setup (DPDT) wiring for high low function on the fans. Does anybody know what the color combination refers to on the SLP fan switch (Hi/Low). There is a black ground strap that is grounded to a stud in the engine bay close to the PCM. There are 3 colors on the SLP fan switch and I'm trying to figure out what each color is for, (Hi, Low, and center off). If anyone can give me the positions on the switch I will wire the SLP wiring into a (DPDT) that is in my EMBLEM PROS switch plate and post the schematic for this switch also.

Gonzo98

iTrader: (7)

Just did this mod, very easy. Took about an hour and was good to go.

96silverram

iTrader: (12)

I actually just figured out the SLP wiring this morning, real easy. Here is a link to the setup.

https://ls1tech.com/forums/appearanc...an-wiring.html

skat

iTrader: (3)

Great write up just finished mine up.

Only problem I could not find anything even close to good for the led's. So I am wired for them and will find some when I go to a better area for stores. And I need to make a panel to cover where the astray goes.

slow

iTrader: (7)

there is nothing in this mod that will prevent a ses light. You can either use resistors to prevent pulling a full ground to the pcm, or do what SLP does in thier fan switch and tap into a hot wire with some components to prevent the pcm from seeing the full ground signal.

Ryan

benoh

iTrader: (13)

ABS plastic and a dremel is your friend. Takes no more than 20 minutes to fab one up. Do you have a Radio Shack around you? Radio Shack carries LEDs and resistors.

RossRinSD

Now that is pimptastic. How did you do the labels? My switch panel has a crapload of switches. Half of them aren't wired to anything, and I'm always worried about turning on my strobes or something accidentally.



and my cheat sheet.