TB bump stop mod question
Thread Starter
Launching!
Joined: Mar 2003
Posts: 213
Likes: 0
From: Central Va
TB bump stop mod question ok not sure if this is the right place for this...but i checked teh TB tsp sensor with me pushing the pedal down all the way it read 45.3 and it could stil be pushed to about 46.2 question i assume this is enough opening but is there a way to take some slack outta the trhottle cable?
Thread Starter
Launching!
Joined: Mar 2003
Posts: 213
Likes: 0
From: Central Va
Re: TB bump stop mod question also i was wondering what should the voltage be for a TB closed at idle? i think mine was like .6?? any info on this so i can understand it better would help...
Re: TB bump stop mod question
I need to know this to and is there any info on how to do this mod
Administrator
Joined: Jan 2002
Posts: 45,841
Likes: 5
From: Earth
Re: TB bump stop mod question You want to be close to 4.7vdc, but don't go past that. You most definitely can remove the slack in your throttle cable. As a matter or fact, you'll have to after doing the TB Bump stop mod.
Thread Starter
Launching!
Joined: Mar 2003
Posts: 213
Likes: 0
From: Central Va
Re: TB bump stop mod question how do you take out the slack?? i've noticed the cable goes from that little black thing to the TB but i don't see any kind of adjustment screw or nothing....
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Re: TB bump stop mod question
how do you take out the slack?? i've noticed the cable goes from that little black thing to the TB but i don't see any kind of adjustment screw or nothing....
Re: TB bump stop mod question slack??? thought it was self adjusting...had no slack issues here...
just dont go past 4.7v DC...I took mine to 4.68v DC....close enough....4.71v DC and it will throw a code.....
just dont go past 4.7v DC...I took mine to 4.68v DC....close enough....4.71v DC and it will throw a code.....
TECH Enthusiast
Joined: Dec 2002
Posts: 546
Likes: 0
From: College Staion, Texas
Re: TB bump stop mod question Does anyone know how to do it with jsut a tester? I know there are wires you can plug into directly on the harness connected to the Tb, I'm just not sure which ones..
Re: TB bump stop mod question http://www.ls1camaro.net/sections.ph...e&artid=26
here is a write up of the bump stop mod done with a volt meter.
here is a write up of the bump stop mod done with a volt meter.
Administrator
Joined: Jan 2002
Posts: 45,841
Likes: 5
From: Earth
Re: TB bump stop mod question
that sounds about right
I did the bump stop mod with a volt meter. It worked like a charm.
