Duals on a Budget PICS/VIDEOS ADDED!!!!!!
#1
Launching!
Thread Starter
iTrader: (27)
Join Date: Oct 2010
Location: Murfreesboro, TN (Nashville)
Posts: 218
Likes: 0
Received 1 Like
on
1 Post
Duals on a Budget PICS/VIDEOS ADDED!!!!!!
Was looking at some of the random mandrel bends laying around the shop and decided to build a custom true dual setup. Longtubes arent in the budget until mid february, so I'll be removing the cats since I tuned out the rear O2's. It'll be 2.5" and go from manifolds to X-pipe to Bullets to dumps before the axle. Started on it today and got the X-pipe almost finished up. Just gotta clean up some of the welds. Whatcha think?
I'm really just tired of the super duper quiet factory exhaust on the car, and I can't stand the Z28 tips. Think it will look a lot cleaner with no tips in the back.
EDIT: Finally got everything installed and I'm really happy with it. No too raspy at all, just a real nice tone. Here's the pics and a short idle vid and a vid of a quick throttle snap.
Idle Vid
Throttle Snap
I'm really just tired of the super duper quiet factory exhaust on the car, and I can't stand the Z28 tips. Think it will look a lot cleaner with no tips in the back.
EDIT: Finally got everything installed and I'm really happy with it. No too raspy at all, just a real nice tone. Here's the pics and a short idle vid and a vid of a quick throttle snap.
Idle Vid
Throttle Snap
Last edited by BRUTL; 01-07-2011 at 06:24 PM.
#4
Launching!
Thread Starter
iTrader: (27)
Join Date: Oct 2010
Location: Murfreesboro, TN (Nashville)
Posts: 218
Likes: 0
Received 1 Like
on
1 Post
Just ordered the Dynomax Bullets and some extra mandrel bends. Plan on installing all of this with my new clutch. I'll take pics and should everything finished up by Friday.
#6
Launching!
Thread Starter
iTrader: (27)
Join Date: Oct 2010
Location: Murfreesboro, TN (Nashville)
Posts: 218
Likes: 0
Received 1 Like
on
1 Post
Xpipe - FREE (Made from spare mandrel bends laying around the shop)
Misc Pipe - FREE (Same thing)
Dynomax Bullets x2 - $80
2 180 Degree Mandrel bend pipes - $44 (just got em to finish up any other bends I may need).
I don't see their name on the sponser list on the right, but I got the Bullets and 180 bends from a company that rhymes with Plummit Placing.
So basically, with the addition of whatever wire I use up while welding, I'm looking at true duals for about $135 plus my time. I don't know about you guys, but that sounds good to me. Assuming I get everything installed this week, I'll get some pics and a video up more towards friday
Misc Pipe - FREE (Same thing)
Dynomax Bullets x2 - $80
2 180 Degree Mandrel bend pipes - $44 (just got em to finish up any other bends I may need).
I don't see their name on the sponser list on the right, but I got the Bullets and 180 bends from a company that rhymes with Plummit Placing.
So basically, with the addition of whatever wire I use up while welding, I'm looking at true duals for about $135 plus my time. I don't know about you guys, but that sounds good to me. Assuming I get everything installed this week, I'll get some pics and a video up more towards friday
Trending Topics
#8
Launching!
Thread Starter
iTrader: (27)
Join Date: Oct 2010
Location: Murfreesboro, TN (Nashville)
Posts: 218
Likes: 0
Received 1 Like
on
1 Post
If you were closer it'd be a go! I have some valve covers, Front cover, and other various items that need to go to the powder coating shop. Shipping exhaust is just too damn expensive.
#11
TECH Senior Member
iTrader: (96)
Join Date: Aug 2007
Location: Turnin' Wrenches Infractions: 005
Posts: 24,240
Likes: 0
Received 79 Likes
on
70 Posts
Also, if there is a product that no site sponsors sell, then generally it is ok to post a link bc you are not competing with sponsor sales. With universal exhaust bends from Summit, you would likely be ok there
#13
Launching!
Thread Starter
iTrader: (27)
Join Date: Oct 2010
Location: Murfreesboro, TN (Nashville)
Posts: 218
Likes: 0
Received 1 Like
on
1 Post
I plan on trimming and bending here and there to accommodate when the headers go on.
I plan on going with some race style pacesetters. I know they don't really break the bank, but with the holidays and just moving into a house, I decided it's better to wait until Feb. The pipe isn't going to cost me any extra running down from the manifolds as we have scrap lengths of tubing all over the place. I plan on hacking off the cats and just welding some pipe and bends up to the flanges that are left over, so I can just bolt it all up to the manifolds for now. O2 sensor bungs are available to me too, so I can mount up the front O2's.
I already have permission to tie up a bay all day on my off, Thursday. Hopefully Summit gets the stuff here on time.
Last edited by BRUTL; 01-01-2011 at 07:20 PM.
#14
Launching!
Thread Starter
iTrader: (27)
Join Date: Oct 2010
Location: Murfreesboro, TN (Nashville)
Posts: 218
Likes: 0
Received 1 Like
on
1 Post
Everything came in today, car is setup on the rack and I'll be in there in the morning installing everything. Expect plenty of pics and a video tomorrow afternoon.
#18
Launching!
Join Date: Apr 2006
Location: Back to Newport News
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
Ok well I'm not too far from u then I stay in the Richneck area near Hall Ford. All the people that seem to wanna race drive some gay *** import that I don't feel like wasting my gas on lol.
#20
Launching!
Join Date: Apr 2006
Location: Back to Newport News
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
Haha must be nice. I guess I won't be keeping up with yall anytime soon then. With a mortgage and pregnant wife the modding funds ain't what they used to be...