If SLP made the 2OTL again, would you buy it?????
#21
I think you could get the 21" long 3inch to work, the bends in the tail pipe might be cheated a little bit. You can cut the outlet tubes down so ther only 1/2 sticking out and weld the tailpipes right to them, the might start with a little of them bend, so stairt on them. But you have room to have them sweep a little wider, and end up in the same spot out the back.
Once those are set you never have to move them anyway. I got my muffler with them with no clamps, just stuck in there really good and never had to remove them. I can take it off with the car and jackstands just sliding the over axle part out.
I'll get a pic were 21 would be.
Once those are set you never have to move them anyway. I got my muffler with them with no clamps, just stuck in there really good and never had to remove them. I can take it off with the car and jackstands just sliding the over axle part out.
I'll get a pic were 21 would be.
#24
I think you could get the 21" long 3inch to work, the bends in the tail pipe might be cheated a little bit. You can cut the outlet tubes down so ther only 1/2 sticking out and weld the tailpipes right to them, the might start with a little of them bend, so stairt on them. But you have room to have them sweep a little wider, and end up in the same spot out the back.
Once those are set you never have to move them anyway. I got my muffler with them with no clamps, just stuck in there really good and never had to remove them. I can take it off with the car and jackstands just sliding the over axle part out.
I'll get a pic were 21 would be.
Once those are set you never have to move them anyway. I got my muffler with them with no clamps, just stuck in there really good and never had to remove them. I can take it off with the car and jackstands just sliding the over axle part out.
I'll get a pic were 21 would be.
ALso 3 inches wider, 9 vs 12
Can you tell me on the tailpipe bends are they the same or one short radius and one long radius? Looks like the outer bend is a short radius and the inner is a long radius.
Last edited by FASTFATBOY; 02-23-2012 at 07:26 PM.
#25
I was adding some pics I already had my Pbucket I have a ton more
I got the case sizes off my 2otL, if you didnt see that too. Its
18 x 9 1/2 x 4 3/4
Uploading some pics of were 21 case would fit?
I got the case sizes off my 2otL, if you didnt see that too. Its
18 x 9 1/2 x 4 3/4
Uploading some pics of were 21 case would fit?
#26
My 2oTL, haha looks whats sharpied in green on it.
this looks like is that SLP 21" case, you can see 12, and 16" marked in red. Thats as big as I have the pic.
Its offset inlet but you can work with that easily
This must be the 2 1/2 inlet truck one
this looks like is that SLP 21" case, you can see 12, and 16" marked in red. Thats as big as I have the pic.
Its offset inlet but you can work with that easily
This must be the 2 1/2 inlet truck one
Last edited by studderin; 02-23-2012 at 07:48 PM.
#29
So far I found 14 pics. even of the SLP ones with a tape measure. haha
Cone
This is a real good pic of the 2OTL, and why its not just a dual/dual with opposite outlets
Heres the dual/dual, thats both outlets. The inlet in on the right. I would think the 2OTL looks lighter too.
Cone
This is a real good pic of the 2OTL, and why its not just a dual/dual with opposite outlets
Heres the dual/dual, thats both outlets. The inlet in on the right. I would think the 2OTL looks lighter too.
Last edited by studderin; 02-23-2012 at 08:04 PM.
#35
#36
I posted them but, it should be public. I got like 14,000
http://s2.photobucket.com/albums/y11/studderin/2OTL/
because race car
#38
#39
I would. Personally I dislike the way my Magnaflow muffler is angled in order to accommodate the right tailpipe, it makes it so I have to drive up on wood to fit a jack under the axle. The 2otl tucks up much better.
#40
My SS came with TOTL, if I want it back I'd have to rip it off my dad's truck. I waited to long to sell it, so he "inherited" it lol. Guess I didn't know at the time they were so sought after.