March vs. ASP Pulley
#1
11 Second Club
Thread Starter
Join Date: Feb 2004
Location: South Texas
Posts: 161
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
What's the best pulley? I'm debating between the March and ASP Pulley. Which is the better package? Anybody know the part # on these Pulley's because I want to make sure I order the correct package. In Thunderracing.com it shows me different packages. Which one does everyone go with?
Thanks on any info!!!!!
Thanks on any info!!!!!
![Burnout](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_burnout.gif)
#5
TECH Enthusiast
iTrader: (7)
Join Date: Jan 2004
Location: Jacksonville, NC
Posts: 740
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I know the march pully weighs 11 pounds compared to 10.5 for the stock pully.
The asp is somewere around 6-7.
That should give you your answer right there.
Though i'm still wondering how this SLP pully is performing.
The asp is somewere around 6-7.
That should give you your answer right there.
Though i'm still wondering how this SLP pully is performing.
#6
TECH Resident
iTrader: (11)
Join Date: Nov 2003
Location: Easley, SC
Posts: 917
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Transamlover33
I know the march pully weighs 11 pounds compared to 10.5 for the stock pully.
#7
TECH Fanatic
iTrader: (9)
Join Date: Feb 2002
Location: West Lafayette, IN
Posts: 1,061
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
From what I remember, the March pulley is heavier than the ASP by several pounds, but is slighty smaller than the ASP. Despite its weight, because it is a fluid dampened pulley, it should be more efficient than the ASP at dissapating power-robbing and potentially harmful crankshaft vibration.
Josh
Josh
Trending Topics
#8
TECH Senior Member
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
OK if you compared an equal weight steel pulley to the March, I could understand the worries. March is FLUID dampened and will definitly outperform any solid pulley in that field. It is 25% underdrive.
One of my next mod with H/C for sure.
One of my next mod with H/C for sure.
#9
wrencher
iTrader: (2)
Join Date: Aug 2002
Location: Chicagoland
Posts: 4,762
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech20year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
The place to look for weight savings is not the balancer.
Lets try to do the same job with less mass?
Wonder why the early ones had knock retard issues?
Little to much crank flex going on there?
There is alot to be said for functionality & longevity of the motor verses saving a few pounds of recipitating weight.
Lets try to do the same job with less mass?
Wonder why the early ones had knock retard issues?
Little to much crank flex going on there?
There is alot to be said for functionality & longevity of the motor verses saving a few pounds of recipitating weight.
#11
Super Moderator
iTrader: (9)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I would steer away from the March. It was the pulley used on the 1150hp engine my friend has. To make it short, the timing chain ended up getting bound up due to bad harmonics. Not saying it isn't a good pulley, but it was removed, changed the timing chain, and used an ATI instead. I believe the ATI is prolly the best bet, but ASP is good also for less $$$.
#14
Sweet Cheeks
iTrader: (7)
Join Date: Aug 2002
Location: Chicago
Posts: 2,277
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
The ATI dampener pulley is superior for harmonically balancing high RPM motors, but it's costly. For a typical street car or car not exceeding normal range RPMs I support the ASP pulley and wouldn't(didn't) pay nearly $500 on a unnecessary pulley.
![The Patriot !!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_patriot.gif)
#17
TECH Addict
iTrader: (4)
Join Date: Nov 2001
Location: Sugar Land, TX
Posts: 2,485
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
The ASP pulley weighs less because the center hub is aluminum. That has nothing to do with dampening and harmonics reductions. The outer ring which is mounted on molded rubber between it and the hub is steel for the necessary weight required to eliminate harmonics.
The newer ASP pulleys are also SFI approved.
The newer ASP pulleys are also SFI approved.
Last edited by Larry; 04-30-2004 at 02:54 PM.
#18
TECH Resident
iTrader: (11)
Join Date: Nov 2003
Location: Easley, SC
Posts: 917
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Alrighty...maybe I'll be buying an ASP instead then. I feel like a ragdoll
What exactly does the SFI approved mean? My only concern with the ASP is I had read about past problems with false KR being reported due to the pulley. Im guessing this has been solved since so many users are using this pulley without problems.
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
#19
TECH Addict
iTrader: (4)
Join Date: Nov 2001
Location: Sugar Land, TX
Posts: 2,485
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by SidewayzOZ
My only concern with the ASP is I had read about past problems with false KR being reported due to the pulley. Im guessing this has been solved since so many users are using this pulley without problems.