Lid to LS3 intake Question
Thread Starter
11 Second Club
Joined: Jun 2010
Posts: 56
Likes: 3
From: Lima
Lid to LS3 intake Question Putting a set of 823's on top of my 6.0 with a ls3 intake, im wondering whats the best lid set up. since the ls6 intake and 799's are going away and going to a bigger diameter intake and was planning on using a LS7 MAF. Its not necessary but just trying to see how everyone else has been doing it, searching high and low but not really seeing to much
I'm not saying it's the best, but I currently use the following.
AEM 28-20118 air filter
FastToys 104 lid (it has issues with cracking though)
Bohnman fast acting themistor
TSP 100mm MAF tube with LS3 MAF
Saxon PC 6:1 honeycomb
Intakehoses.com 22L40 intake tube
Nick Williams 92mm TB
AEM 28-20118 air filter
FastToys 104 lid (it has issues with cracking though)
Bohnman fast acting themistor
TSP 100mm MAF tube with LS3 MAF
Saxon PC 6:1 honeycomb
Intakehoses.com 22L40 intake tube
Nick Williams 92mm TB
Thread Starter
11 Second Club
Joined: Jun 2010
Posts: 56
Likes: 3
From: Lima
yes right now i just have some off brand 92mm throttle body i was going to use. next year or so ill eventually throw ON3 twins kit on the car but right now for this season i was doing 823's and TSP F35 cam. Being the car has a 4k stall and 4.56 gears from already having a ms4 in the car i just opted for another donkey dick cam.
Thread Starter
11 Second Club
Joined: Jun 2010
Posts: 56
Likes: 3
From: Lima
I'm not saying it's the best, but I currently use the following.
AEM 28-20118 air filter
FastToys 104 lid (it has issues with cracking though)
Bohnman fast acting themistor
TSP 100mm MAF tube with LS3 MAF
Saxon PC 6:1 honeycomb
Intakehoses.com 22L40 intake tube
Nick Williams 92mm TB
AEM 28-20118 air filter
FastToys 104 lid (it has issues with cracking though)
Bohnman fast acting themistor
TSP 100mm MAF tube with LS3 MAF
Saxon PC 6:1 honeycomb
Intakehoses.com 22L40 intake tube
Nick Williams 92mm TB
With my 104 lid to NW 102 TB I found the silicone 22 degree couplers many use made taking the lid on and off a major pain. I ended up getting a 4" spectre 9775 accordion style bellow that makes it a lot easier to get to the air filter. They may make a smaller diameter one for your 92mm setup, or maybe even this one would work depending on the OD of your MAF and TB.
Yeah, the top of mine is scuffed where it rubs against the bottom of the hood. I also found a crack in the leading edge a few nights ago, something like super glue may seal it.
Trending Topics
Thread Starter
11 Second Club
Joined: Jun 2010
Posts: 56
Likes: 3
From: Lima
With my 104 lid to NW 102 TB I found the silicone 22 degree couplers many use made taking the lid on and off a major pain. I ended up getting a 4" spectre 9775 accordion style bellow that makes it a lot easier to get to the air filter. They may make a smaller diameter one for your 92mm setup, or maybe even this one would work depending on the OD of your MAF and TB.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo Thread Starter
11 Second Club
Joined: Jun 2010
Posts: 56
Likes: 3
From: Lima
i thought about doing their smaller 98mm lid, but then i run into which maf which i was maybe just gonna end up using the stock maf for now until i went boost cause the lid goes away after that and itll be easier to switch to a card style with the room itll create getting rid of the short run between lid and throttle body
