AZ Power & sound / Pro Dyno true duals OVER axle (PICS)
#24
TECH Resident
Thread Starter
iTrader: (2)
Join Date: May 2003
Location: Tempe, AZ
Posts: 840
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Tiger2o69
Looks damn good but that a whole lot of money
There is just a lot of labor involved since we dont use a pipe bender at all, all pipes are cut to size and welded for best flow, and we build the Xpipes in house... not to mention we use only the highest grade stainless steel, which im living proof of that looks the same as it did the day it went on even 2 years later
#25
11 Second Club
iTrader: (16)
Join Date: May 2004
Location: MS
Posts: 2,223
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SSOnYourSix
Cant put a price on perfection
There is just a lot of labor involved since we dont use a pipe bender at all, all pipes are cut to size and welded for best flow, and we build the Xpipes in house... not to mention we use only the highest grade stainless steel, which im living proof of that looks the same as it did the day it went on even 2 years later
There is just a lot of labor involved since we dont use a pipe bender at all, all pipes are cut to size and welded for best flow, and we build the Xpipes in house... not to mention we use only the highest grade stainless steel, which im living proof of that looks the same as it did the day it went on even 2 years later
#27
TECH Fanatic
iTrader: (4)
Join Date: Feb 2003
Location: bridgwater, nj
Posts: 1,527
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by SSOnYourSix
Cant put a price on perfection
There is just a lot of labor involved since we dont use a pipe bender at all, all pipes are cut to size and welded for best flow, and we build the Xpipes in house... not to mention we use only the highest grade stainless steel, which im living proof of that looks the same as it did the day it went on even 2 years later
There is just a lot of labor involved since we dont use a pipe bender at all, all pipes are cut to size and welded for best flow, and we build the Xpipes in house... not to mention we use only the highest grade stainless steel, which im living proof of that looks the same as it did the day it went on even 2 years later
#28
TECH Senior Member
iTrader: (6)
Originally Posted by Lane
Easy on pics and price quoting there. Dangerous threads like these can educate the board about other products out there besides those sponsors sell...
The problem comes in when you start using this board to pimp your product and without becoming a sponsor
#30
Originally Posted by SSOnYourSix
Cant put a price on perfection
There is just a lot of labor involved since we dont use a pipe bender at all, all pipes are cut to size and welded for best flow, and we build the Xpipes in house... not to mention we use only the highest grade stainless steel, which im living proof of that looks the same as it did the day it went on even 2 years later
There is just a lot of labor involved since we dont use a pipe bender at all, all pipes are cut to size and welded for best flow, and we build the Xpipes in house... not to mention we use only the highest grade stainless steel, which im living proof of that looks the same as it did the day it went on even 2 years later
#31
TECH Resident
Thread Starter
iTrader: (2)
Join Date: May 2003
Location: Tempe, AZ
Posts: 840
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by WILWAXU
You can post all the technical information and pictures about any product you like.
The problem comes in when you start using this board to pimp your product and without becoming a sponsor
The problem comes in when you start using this board to pimp your product and without becoming a sponsor
#32
TECH Resident
Thread Starter
iTrader: (2)
Join Date: May 2003
Location: Tempe, AZ
Posts: 840
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by V8er
Looks good What size pipes are you using for the dual cat back section?
#34
TECH Resident
iTrader: (1)
Join Date: Nov 2001
Location: Vertigo
Posts: 955
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by WILWAXU
The problem comes in when you start using this board to pimp your product and without becoming a sponsor
I would like to become a sponsor, but $95/month is too much for a struggling little family business... So, for now, I guess I'll remain at www.notasponsor.com...
#39
TECH Resident
Thread Starter
iTrader: (2)
Join Date: May 2003
Location: Tempe, AZ
Posts: 840
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by MeentSS02
Nevermind the question...upon closer inspection and seeing that there is a driveshaft loop attached to it, it looks like a BMR piece.
#40
TECH Addict
Join Date: Mar 2004
Location: Fat Chance Hotel
Posts: 2,336
Likes: 0
Received 0 Likes
on
0 Posts
I was just about to do a search on this section for pics of a siamesed dual exhaust over the axle then low and behold....
Looks really nice. Also looks like alumized pipe to me, but that could be the picture/lighting playing tricks on me. :
I am planning on building an exhaust like this one for my own car. If you don't mind me asking...about how much $$$ for the parts alone for the buildup?
Looks really nice. Also looks like alumized pipe to me, but that could be the picture/lighting playing tricks on me. :
I am planning on building an exhaust like this one for my own car. If you don't mind me asking...about how much $$$ for the parts alone for the buildup?