Anyone Sell Just an Over the Axle Pipe?
Re: Anyone Sell Just an Over the Axle Pipe? Dynomax sells complete mandrel bent 3" systems (just the piping), from i-pipe, over axle, tailpipes. Just use whatever muffler you desire.
Summit and jegs has all the pieces. I paid just over 100$ I think for all the pieces. Not bad!
This is the over axle piece on my floor:
<img src="http://www.fear.net/~dope/camaro/exhaust/catback/dynomax_overaxlepipe1.jpg" alt=" - " />
Very nice pieces. Non stainless.
Dope
Summit and jegs has all the pieces. I paid just over 100$ I think for all the pieces. Not bad!
This is the over axle piece on my floor:
<img src="http://www.fear.net/~dope/camaro/exhaust/catback/dynomax_overaxlepipe1.jpg" alt=" - " />
Very nice pieces. Non stainless.
Dope
Re: Anyone Sell Just an Over the Axle Pipe? Thanks Dope
Picture and all. Nice. What muffler are you going to go with? Ultraflo?
I think I am going to go with that set up. 100 bucks! You cant beat that. Get the flowmaster y and have a shop make some mandrel 2.5" pipes after the cats running into the y and run it into the dyno make Ipipe and out an ultraflo muffler. <img border="0" alt="[cheers]" title="" src="graemlins/gr_cheers.gif" /> <img border="0" alt="[chug]" title="" src="graemlins/gr_chug.gif" /> <img border="0" alt="[cheers]" title="" src="graemlins/gr_cheers.gif" />
Picture and all. Nice. What muffler are you going to go with? Ultraflo?
I think I am going to go with that set up. 100 bucks! You cant beat that. Get the flowmaster y and have a shop make some mandrel 2.5" pipes after the cats running into the y and run it into the dyno make Ipipe and out an ultraflo muffler. <img border="0" alt="[cheers]" title="" src="graemlins/gr_cheers.gif" /> <img border="0" alt="[chug]" title="" src="graemlins/gr_chug.gif" /> <img border="0" alt="[cheers]" title="" src="graemlins/gr_cheers.gif" />
TECH Enthusiast
Joined: Nov 2001
Posts: 677
Likes: 0
From: Baton Rouge, La. and sometimes Houston Tx
Re: Anyone Sell Just an Over the Axle Pipe? You think two of those pipes would fit over the axle with the upper panhard rod out if you ran it on the passenger side?
Re: Anyone Sell Just an Over the Axle Pipe? The exhaust is actually on the car, that's an old pic before I installed it. I am running FLP longtubes with a 12" dynomax bullet on the i-pipe, followed by a cutout, followed by the over-axle piping an a dynomax ultraflow.
Got a mccord power cutout valve on the cutout, which I run open most of the time. Close it up for stealth mode <img border="0" title="" alt="[Smile]" src="gr_stretch.gif" />
Dope
Got a mccord power cutout valve on the cutout, which I run open most of the time. Close it up for stealth mode <img border="0" title="" alt="[Smile]" src="gr_stretch.gif" />
Dope
Re: Anyone Sell Just an Over the Axle Pipe? Also, good freakin' luck. You can barely fit one of them in there! I actually had to re-adjust my hangers because it's so close tolerances with just the single 3". If your car's lower than mine then you're really in trouble.
Dope
Dope
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo Re: Anyone Sell Just an Over the Axle Pipe? Hey dug,
I have the dynomax 17227, 3" in and dual 2.5" out. It's very quiet. When I had it with my stock manifolds/cats, it was QUIETER than stock. Now, with FLP longtubes it's still very quiet. You can barely even hear it inside the car. It sounds pretty decent outside the car (I had a friend drive around in it once so I could hear it). I run my cutout open 98% of the time anyway so I don't care, the muffler is only for stealth mode (and it works great for that, and flows awesome too).
Dope
I have the dynomax 17227, 3" in and dual 2.5" out. It's very quiet. When I had it with my stock manifolds/cats, it was QUIETER than stock. Now, with FLP longtubes it's still very quiet. You can barely even hear it inside the car. It sounds pretty decent outside the car (I had a friend drive around in it once so I could hear it). I run my cutout open 98% of the time anyway so I don't care, the muffler is only for stealth mode (and it works great for that, and flows awesome too).
Dope
