How much should I charge for a pulley install tool?
#21
^^^ That's good insight. People spend hundreds per month on payments and insurance and won't spend jack to fix/modify their rides correctly.
I may just get some longer bolts and sell 'em for $4
******************************************
Brandon Boomhauer - The wires (if 8mm Taylor -what I run- any color) can be had for $85 with boots that will need to be crimped. The crimp tool is about $6.
So you have a complete kit with the type/color wires you choose for $146 including color instructions and polished brackets!!! There are (2) tools that would make the install much easier, a 90 degree drill attachment and a windshield wiper arm puller $30 total. So for $175 you have a 100% complete kit with everything you need to do a high quality job. Compare it to any other kit on the market....
Some guys will want the 90 degree boots to run between the headers and heads for the hidden look, and some will want the straight style to stick out like the factory ones. You can set the amount of slop (if you want custom routing) when you do the cut/crimp. ~Joshua
I may just get some longer bolts and sell 'em for $4
******************************************
Brandon Boomhauer - The wires (if 8mm Taylor -what I run- any color) can be had for $85 with boots that will need to be crimped. The crimp tool is about $6.
So you have a complete kit with the type/color wires you choose for $146 including color instructions and polished brackets!!! There are (2) tools that would make the install much easier, a 90 degree drill attachment and a windshield wiper arm puller $30 total. So for $175 you have a 100% complete kit with everything you need to do a high quality job. Compare it to any other kit on the market....
Some guys will want the 90 degree boots to run between the headers and heads for the hidden look, and some will want the straight style to stick out like the factory ones. You can set the amount of slop (if you want custom routing) when you do the cut/crimp. ~Joshua
#22
TECH Senior Member
iTrader: (10)
Joined: Nov 2001
Posts: 8,766
Likes: 0
From: Gainesville, Denton TX
Yeah, I know what they need to work. I was the person to tell you about the 90* boots and how to make them work. In fact I was the first person on here do such a thing. If you actually had tried 90* boots you would see how they can not work.
#23
Originally Posted by Brandon Boomhauer
Yeah, I know what they need to work. I was the person to tell you about the 90* boots and how to make them work. In fact I was the first person on here do such a thing. If you actually had tried 90* boots you would see how they can not work.
I'm actually running 90 degree boots now (until last week when I started the turbo install)... The wires used the 90 from the cylinder behind it to "hook" it and keep it away from the headers. I also had a copper wire that I used the keep them bundled. The whole bundle exits the back and runs up the firewall to the coil bricks.
I have to change to straight boots now, because the twin turbo manifolds have nowhere near the clearance between the heads that my old Hooker longtubes had.
#24
I like 618Hawk's tool better than the one shown in this thread. I just bought a loinget bolt & washer and use that. for the right price I would buy 618Hawk's tool also.
I did make a lot of my own tools for cam installs.
To hold the pully still
Valvespring tool.
It needed a better "Threaded rod".
I did make a lot of my own tools for cam installs.
To hold the pully still
Valvespring tool.
It needed a better "Threaded rod".
#26
Originally Posted by FIREHAWK#608
... People spend hundreds per month on payments and insurance and won't spend jack to fix/modify their rides correctly... ~Joshua
#29
You could sell EGR/AIR blockoff kits. It could come with all the plates you need AND the 1-3/8" adjustable freeze plug as well. If people have to wait for plates to come in, they might as well get the freeze plug from you too.
#30
Originally Posted by TheBlurLS1
You could sell EGR/AIR blockoff kits. It could come with all the plates you need AND the 1-3/8" adjustable freeze plug as well. If people have to wait for plates to come in, they might as well get the freeze plug from you too.
#32
Originally Posted by 2xLS1
Explain why and go into detail.
#34
Originally Posted by davered00ss
...I just use a longer bolt...
#35
Just thought I would share a bit of info on my dampner install tool.
I feel it works rather well. And all those that have used it agree.
Here are a few reasons why.
With the threaded pusher section it acts as a handle to help hold the pulley in position, due to the large area washer at the bottom is the same diameter as the recessed area with in the dampner.
There are fewer moving parts to deal with, no loose washer or spacers.
Once tool and dampner are in place there is plenty of room to use a wrench to crank it on. Vs trying to get a wrench down inside of the dampner. Which I 1st noted problems with the 1st time I tryed a section of all thread, with just a nut and washer.
I can say, I have never used a longer bolt to push it on but have heard nothing but bad results. Due to bolts being to short and causing damage to the first few threads.
Some may say that my washer is a cheap way to go but if I were to add a thrust bearing, the cost would be much more. For something that would not help that much more, and appears not to be a issue.
I have looked the the autozone unit and it did not work with the LS1. At least the kit from my local store.
Here is the orginal thread.
https://ls1tech.com/forums/removed-locked-thread-graveyard/391883-new-crank-dampener-installation-tool-pics.html
Sorry if I stepped on any toes not asking to sell prior to, my fault. But if you look at my trader rating you will see all are happy.
Chris
I feel it works rather well. And all those that have used it agree.
Here are a few reasons why.
With the threaded pusher section it acts as a handle to help hold the pulley in position, due to the large area washer at the bottom is the same diameter as the recessed area with in the dampner.
There are fewer moving parts to deal with, no loose washer or spacers.
Once tool and dampner are in place there is plenty of room to use a wrench to crank it on. Vs trying to get a wrench down inside of the dampner. Which I 1st noted problems with the 1st time I tryed a section of all thread, with just a nut and washer.
I can say, I have never used a longer bolt to push it on but have heard nothing but bad results. Due to bolts being to short and causing damage to the first few threads.
Some may say that my washer is a cheap way to go but if I were to add a thrust bearing, the cost would be much more. For something that would not help that much more, and appears not to be a issue.
I have looked the the autozone unit and it did not work with the LS1. At least the kit from my local store.
Here is the orginal thread.
https://ls1tech.com/forums/removed-locked-thread-graveyard/391883-new-crank-dampener-installation-tool-pics.html
Sorry if I stepped on any toes not asking to sell prior to, my fault. But if you look at my trader rating you will see all are happy.
Chris
#36
^^^ That does look like a very nice tool. If the user simply lubes the washer on the contact surfaces with light grease that should take care of any friction.
If any body wants to add a neat tool to my site they're more than welcome and you can drop ship it to customers.
If somebody has a tool that they want listed feel free to call or Pm. 678/492/6843 ~Joshua
If any body wants to add a neat tool to my site they're more than welcome and you can drop ship it to customers.
If somebody has a tool that they want listed feel free to call or Pm. 678/492/6843 ~Joshua
#37
Thanks Josh
As it is I have even been supplying a small packet of high quality grease to go along with the tool. Which is applied between the pusher section and the thrust washer. Like I said no problems so far.
Might take you up on your site.................
Chris
As it is I have even been supplying a small packet of high quality grease to go along with the tool. Which is applied between the pusher section and the thrust washer. Like I said no problems so far.
Might take you up on your site.................
Chris
#38
Originally Posted by 618HAWK
Thanks Josh
As it is I have even been supplying a small packet of high quality grease to go along with the tool. Which is applied between the pusher section and the thrust washer. Like I said no problems so far.
Might take you up on your site.................
Chris
As it is I have even been supplying a small packet of high quality grease to go along with the tool. Which is applied between the pusher section and the thrust washer. Like I said no problems so far.
Might take you up on your site.................
Chris