How to: Remove Powerbond UD Pulley
#1
How to: Remove Powerbond UD Pulley
I searched on this topic, and the results came up pretty sparse on how to remove one of these underdrive pulleys. I figured out how to do it, and the instructions will be listed below. Keep in mind that this is for this particular pulley only...this method may not work on other brands.
Powerbond Pulley Removal:
Tools needed -
- Late Model Chrysler Harmonic Balancer Puller (available as a rental at your local Auto Zone)
- 15/16" socket to turn the bolt on the puller
- 6" long, 3/8" extension
- 24mm socket to remove GM torque to yield harmonic balancer bolt
Steps -
1. Remove the balancer bolt. A 24mm socket should fit the head, and you'll most likely need a breaker bar with a cheater.
2. Grab the late model Chrysler harmonic balancer puller. There will be 4 items in the box - the jaws, a bolt, and two rods. You'll need the smaller of the two rods in the box for this method.
3. Insert the 6" long, 3/8" extension in the end of the crank and bottom it out on the back of the hole in the crank snout. There won't be much sticking out after it is in there.
4. Grab the puller. Thread the supplied bolt in a little ways, and put the smaller rod in the end of the bolt. Make sure that rod fits in the 3/8" extension. It is a tight fit, but I assure you, it will fit. The jaws will grab on to the outside edge of the pulley. It did no damage that I saw.
5. Start cranking away on the bolt...I didn't even have to use a breaker bar to get it to move, but when it finally gave way, there was a pretty good pop and then it slid much more easily.
And that's it. Don't waste your time with a large 3 jaw puller...the late model Chrysler puller is MUCH nicer since it keeps the rod that pushes against the crank centered. At first glance, the Chrysler puller doesn't look like it would be large enough to fit around the outside of the pulley, but it does (just barely). This most likely wouldn't work on a larger diameter pulley (like the stock one).
Hope that helps someone out in the future. It took me 10 minutes to get the damn thing off, whereas the 3-jaw puller didn't even budge the pulley.
Powerbond Pulley Removal:
Tools needed -
- Late Model Chrysler Harmonic Balancer Puller (available as a rental at your local Auto Zone)
- 15/16" socket to turn the bolt on the puller
- 6" long, 3/8" extension
- 24mm socket to remove GM torque to yield harmonic balancer bolt
Steps -
1. Remove the balancer bolt. A 24mm socket should fit the head, and you'll most likely need a breaker bar with a cheater.
2. Grab the late model Chrysler harmonic balancer puller. There will be 4 items in the box - the jaws, a bolt, and two rods. You'll need the smaller of the two rods in the box for this method.
3. Insert the 6" long, 3/8" extension in the end of the crank and bottom it out on the back of the hole in the crank snout. There won't be much sticking out after it is in there.
4. Grab the puller. Thread the supplied bolt in a little ways, and put the smaller rod in the end of the bolt. Make sure that rod fits in the 3/8" extension. It is a tight fit, but I assure you, it will fit. The jaws will grab on to the outside edge of the pulley. It did no damage that I saw.
5. Start cranking away on the bolt...I didn't even have to use a breaker bar to get it to move, but when it finally gave way, there was a pretty good pop and then it slid much more easily.
And that's it. Don't waste your time with a large 3 jaw puller...the late model Chrysler puller is MUCH nicer since it keeps the rod that pushes against the crank centered. At first glance, the Chrysler puller doesn't look like it would be large enough to fit around the outside of the pulley, but it does (just barely). This most likely wouldn't work on a larger diameter pulley (like the stock one).
Hope that helps someone out in the future. It took me 10 minutes to get the damn thing off, whereas the 3-jaw puller didn't even budge the pulley.
#3
Originally Posted by theblur98ss
I've heard the 3 jaw puller can pull the balancer apart.
Trending Topics
#8
I have the craftsman harmonic damper puller and it's worked on all the ones I've used it on. I had a cheapy one time and I had to grind to get it to work. Those 3 holes are there for a reason.....use them.
#16
You bet he is. I got the name wrong in the post above, but here is the thread:
https://ls1tech.com/forums/showthrea...highlight=tool
Worth every damn penny, and he is a great guy to deal with. IMO, the pulley went on MUCH easier than it came off.
https://ls1tech.com/forums/showthrea...highlight=tool
Worth every damn penny, and he is a great guy to deal with. IMO, the pulley went on MUCH easier than it came off.
#18
This is an old thread but it helped me out big time today so I thought I would contribute to it just a little. This technique can also be used to remove the stock Corvette LS2 balancer.
The AutoZone part number is : OEM# 27139 Chrysler Harmonic Puller
This is what you will get:
This tool is great because it is a direct fit for OEM balancers.
Thumbs up to you MeentSS02
The AutoZone part number is : OEM# 27139 Chrysler Harmonic Puller
This is what you will get:
This tool is great because it is a direct fit for OEM balancers.
Thumbs up to you MeentSS02
#20
Banned
iTrader: (47)
Join Date: Oct 2011
Location: Wisconsin
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
for some reason or nother, this isn't working out for me! i can not get all 3 hooks over the pulley lip. mine is a powerbond, 25% underdriven.
anyone have pix of it installed on the pulley lip????
anyone have pix of it installed on the pulley lip????