well my engine went bye bye lol
04-11-2010, 02:13 PM
#121
yeah actually i have, here's my finally pulling out the motor in the racer's lounge. i'm payin the deposit to SDPC end of the month for my forged engine and once i get it from them i'll post pics and the specs of it
04-12-2010, 10:49 AM
#122
Teching In
Join Date: Mar 2009
Location: Houston, TX
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
yeah actually i have, here's my finally pulling out the motor in the racer's lounge. i'm payin the deposit to SDPC end of the month for my forged engine and once i get it from them i'll post pics and the specs of it
06-29-2010, 07:39 AM
#125
Teching In
Join Date: Mar 2009
Location: Houston, TX
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Well I hope you have better luck than I, guy sold my **** and him working for the prison made the cops tell me to go **** myself when he fabricated a good enough story.
06-29-2010, 07:55 AM
#127
Teching In
Join Date: Mar 2009
Location: Houston, TX
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
You would have had to have been following the whole story. Guy was supposed to be watching my car, got all shady as soon as I deployed to Iraq, and now I'm saying he just sold it. SInce he works for the prison, the cops pretty much gave me the finger.
07-21-2010, 11:57 PM
#130
started out as just a bare long block, with no front accessories on it and then quickly we did this
we put most of my old stuff off my engine since it was running good back onto this one
and after a quick run to the dealership to get some extra headers bolts and order a new brake line, this is what we finished with today
the things i need to run start the car is a new water pump, a torque converter, the brake line and exhaust. tomorrow is puttin the wiring back in place
we put most of my old stuff off my engine since it was running good back onto this one
and after a quick run to the dealership to get some extra headers bolts and order a new brake line, this is what we finished with today
the things i need to run start the car is a new water pump, a torque converter, the brake line and exhaust. tomorrow is puttin the wiring back in place
07-24-2010, 06:50 PM
#131
well the engine is in and the bolts are up, i'm just waiting on the brake line before i snug the body bolts up. i'm having some difficulty remembering where wires go, mainly for the starter 
anyone have write ups or pics of starters they pulled off and put on? i'd like to see where the negative and positive wires from the battery go and where the ground wire goes thats on the same line as the sensor that plugs into the oil pan
anyone have write ups or pics of starters they pulled off and put on? i'd like to see where the negative and positive wires from the battery go and where the ground wire goes thats on the same line as the sensor that plugs into the oil pan
07-27-2010, 02:16 PM
#132
went by the transmission shop and everything is almost finished 
just need the driveshaft installed and the car should be ready for me to tow home and finish the wiring 
still need my exhaust put on, can't run around with open header for long lol
just need the driveshaft installed and the car should be ready for me to tow home and finish the wiring still need my exhaust put on, can't run around with open header for long lol
07-28-2010, 08:02 PM
#133
well here is the start up after i picked up a EGR plug for the manifold, first time without it the engine shot up to 4000rpm lol
i still need to hook up the driver side brake line and put fluid in then it's off to the gas station for some gas for my baby and then get the exhaust put on
i still need to hook up the driver side brake line and put fluid in then it's off to the gas station for some gas for my baby and then get the exhaust put on
