Generation III Internal Engine 1997-2006 LS1 | LS6
Sponsored by:
Sponsored by:

HELP oil pressure issues

Thread Tools
 
Search this Thread
 
Old Jan 26, 2012 | 08:11 PM
  #1  
hglenn's Avatar
Thread Starter
Teching In
 
Joined: Dec 2011
Posts: 15
Likes: 0
Default HELP oil pressure issues

well iv got a 1998 camaro ls1 m6 car. the car has a cam and a few other bolt ons. i took the car out for a drive tonight and i noticed the oil pressure was around 20 psi at idle and jumping a little bit. the car normaly runs around 40 at idle so can any one tell me was wrong. im guessing oil pump failure
Reply
Old Jan 26, 2012 | 08:25 PM
  #2  
SOMbitch's Avatar
TECH Senior Member
iTrader: (8)
 
Joined: Sep 2007
Posts: 6,881
Likes: 3
Default

Being that it is a 98 it is and it just started out of nowhere that is entirely possible... Check with a manual gauge and go from there IMO..
Reply
Old Jan 26, 2012 | 08:27 PM
  #3  
LS1MCSS's Avatar
TECH Junkie
iTrader: (18)
 
Joined: Jan 2006
Posts: 3,831
Likes: 8
From: Dover, Arkansas
Default

Originally Posted by hglenn
well iv got a 1998 camaro ls1 m6 car. the car has a cam and a few other bolt ons. i took the car out for a drive tonight and i noticed the oil pressure was around 20 psi at idle and jumping a little bit. the car normaly runs around 40 at idle so can any one tell me was wrong. im guessing oil pump failure
Did you check the oil level?
Reply
Old Jan 26, 2012 | 08:53 PM
  #4  
hglenn's Avatar
Thread Starter
Teching In
 
Joined: Dec 2011
Posts: 15
Likes: 0
Default

yeah oild level seemed fine whats the best pump to buy when being on a budget and with no mods
Reply
Old Jan 27, 2012 | 01:08 AM
  #5  
mannyman84's Avatar
TECH Enthusiast
iTrader: (2)
 
Joined: May 2007
Posts: 638
Likes: 2
From: Hawthorne CA
Default

Check the oil pressure with a gauge. How many miles on it? 20 psi is acceptable and with in specs. If you have good pressure with a manual Gauge then change your oil switch.
Reply
Old Jan 27, 2012 | 05:22 AM
  #6  
mark21742's Avatar
TECH Addict
 
Joined: Sep 2009
Posts: 2,481
Likes: 5
From: PA/MD
Default

If you replace the pump I'll recomend a melling pump
Reply
Old Jan 27, 2012 | 08:17 AM
  #7  
hglenn's Avatar
Thread Starter
Teching In
 
Joined: Dec 2011
Posts: 15
Likes: 0
Default

the car just hit 61k and whats the quickest way to put a gauge on it
Reply
Old Jan 27, 2012 | 08:36 AM
  #8  
trans_am7935's Avatar
TECH Fanatic
15 Year Member
iTrader: (15)
 
Joined: Mar 2009
Posts: 1,453
Likes: 3
From: Glen Burnie, MD
Default

when i first bought my car it would idle at 35-40psi hot all the time, then one day it just dropped to 20psi, i immediately changed the oil and found a fram filter on there. i cut the filter open (as i always do on my oil changes) and found the paper POS filter to be collapsed and folded all up inside. got the car started back up with Mobile 1 (this was about 5-6 years ago when they were still good) and a new filter, and the psi was back up to 40psi hot idle
Reply
Old Jan 27, 2012 | 04:35 PM
  #9  
hglenn's Avatar
Thread Starter
Teching In
 
Joined: Dec 2011
Posts: 15
Likes: 0
Default

see i fired up today and drove it to work and the oil pressure was fine and it never droped. now im pretty mind fucked but will do a oil change with a k&n filter
Reply




All times are GMT -5. The time now is 03:03 PM.