Head stud question
Thread Starter
On The Tree
Joined: Jul 2010
Posts: 130
Likes: 0
Head stud question I have a new tsp 347 that I ordered and want to use the 234-4316 12 point pro kit that I have.
Block was a 5.3 aluminum block and my heads are 243's anyone know if this kit will work? If not what size studs should I be using? I've heard that I have only a couple different studs that would need to be used ....
Any help would be appreciated!
Block was a 5.3 aluminum block and my heads are 243's anyone know if this kit will work? If not what size studs should I be using? I've heard that I have only a couple different studs that would need to be used ....
Any help would be appreciated!
TECH Junkie
Joined: Nov 2013
Posts: 3,913
Likes: 366
From: White Bear, Mn
Yes, they will work. You previously used them in a 5.3 ?
You should have 8 long bolts 2 med bolts and 5 small bolts per head.
After 2004...2005... They were all medium bolts (4in.) and small bolts by the intake manifold.
You should have 8 long bolts 2 med bolts and 5 small bolts per head.
After 2004...2005... They were all medium bolts (4in.) and small bolts by the intake manifold.
The alum 5.3 block should have used the 4317. The 4316 will work in the ls1 block only if its an early block. the only way to tell visually is to look in the center holes and see where the threads begin. if they are close to the deck the 4316 wont work if they are quite a way down in the hole they will. or compare the outer top large head bolt holes with the others. if they look identical the 4317 will work, if they are very diff the 4316 will work.
The studs fit the block, not the heads. the heads dont matter.
Unless you are saying that tsp built a 347 out of the 5.3l alum block. if so itll use the 4317 studs.
The studs fit the block, not the heads. the heads dont matter.
Unless you are saying that tsp built a 347 out of the 5.3l alum block. if so itll use the 4317 studs.
Thread Starter
On The Tree
Joined: Jul 2010
Posts: 130
Likes: 0
I'll buy the whole kit if I have to, but could anyone tell me if I can just purchase the bolts I need to complete the kit that I already have? I've been told that I'm only short 2-4 bolts total from the right kit....
Trending Topics
The only parts that will work off the 4316 on a pre 04 block are the top 8mm small studs (10) and the 2 top short studs. the 04+ use all that same short length. actually you have only 2 large studs that will work. the rest are WAY too long.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
