Need help! H/C install
12-30-2005, 11:49 PM
#82
Staging Lane
Join Date: Aug 2005
Location: Crestview, FL
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
I did not read threw this whole thread. So if you got it running congrats! But if not I had a very similar situation with an automatic. I put everything together I knew it was all correct, but it would just crank crank crank and not start! Well what happen was since I did not have the tune on it the computer was having a hard time with the cam.. It was a cheaTR cam too. Anyway I got it running by have the gas petal stuck to the floor like my foot was going to go threw it and cranked it. It finally started! Hope your problem is the same as mine and you get it running if you have not already. Oh I have gotten that car tuned and it runs great now! Good cam. 
12-30-2005, 11:52 PM
#83
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
good to hear man, glad you got your problems worked out 
Same deal here but I checked for spark and there was none. I have cranked and cranked with no fire.
Same deal here but I checked for spark and there was none. I have cranked and cranked with no fire.
12-30-2005, 11:59 PM
#84
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
Aight I just went out there and check over the pcm.
I loosend the bolt on the front part of the pcm a week or so ago cause I thought I was going to send it off to TSP that day; but I didnt. I just went out there and for ***** and giggles I went to tighten those bolts down to make sure they were in good...one was completely loose.
I actually remember pulling on it to get it out, then left it 
.
Sooooooooooooo...is my problem solved you think?
The coils are off right now and I am tired as hell so tommarow I will put them back on and try to fire it up.
I loosend the bolt on the front part of the pcm a week or so ago cause I thought I was going to send it off to TSP that day; but I didnt. I just went out there and for ***** and giggles I went to tighten those bolts down to make sure they were in good...one was completely loose.
I actually remember pulling on it to get it out, then left it .Sooooooooooooo...is my problem solved you think?
The coils are off right now and I am tired as hell so tommarow I will put them back on and try to fire it up.
12-31-2005, 02:22 PM
#89
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
I let it run for a good 5 to 7 seconds...never came up.
Where should I start?
Should I try again?
I took extra care getting the o ring on right.
That oil pressure sending unit in the back of the manifold is fine.
Where should I start?
Should I try again?
I took extra care getting the o ring on right.
That oil pressure sending unit in the back of the manifold is fine.
Last edited by Lithium; 12-31-2005 at 02:40 PM.
12-31-2005, 03:30 PM
#91
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
If the O ring is fucked up wouldnt pressure still come up though?
Maybe I installed one of the spacers wrong...heard people say that will cause 0 pressure.
I really think I installed it all right though
Maybe I installed one of the spacers wrong...heard people say that will cause 0 pressure.
I really think I installed it all right though
12-31-2005, 05:07 PM
#99
Wow, I just read thru this thread. My heart is breaking as I am in the middle of a complete engine swap and have never done one before. I hope mine starts when I turn the key and I have pressure.
Thank you for sharing your pain so that others (read I) can learn from it and avoid the pitfalls. I am subscribed.
Good luck!!!
Thank you for sharing your pain so that others (read I) can learn from it and avoid the pitfalls. I am subscribed.
Good luck!!!
12-31-2005, 05:08 PM
#100
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
lol seriously its never ending. I mean the pcm was loose big deal, **** happens. I did a lot or uncessary work but she started.
Now this! I know I installed that ****** correctly.
Now this! I know I installed that ****** correctly.