Trick Flow Heads
TECH Resident
Joined: Dec 2004
Posts: 881
Likes: 1
Other than the flow number, I'm interested in the combustion. Some other TF heads, the Ford 'R's come to mind, have the plug seriously pointed toward the exhaust.
So more than the flow bench, I'd really like to see the results of these heads with a strong cam, like 224/228 LSK, and good intake. I'd really like to see the spark advance numbers, and maybe the amount of compression that could be tolerated.
Mike@TEA could chime in, do you expect these heads to require less advance and use more compression?
So more than the flow bench, I'd really like to see the results of these heads with a strong cam, like 224/228 LSK, and good intake. I'd really like to see the spark advance numbers, and maybe the amount of compression that could be tolerated.
Mike@TEA could chime in, do you expect these heads to require less advance and use more compression?
Originally Posted by skipperbisket
you consider a 224/228 cam a "strong" cam? i wanna see what these heads do with a real cam, like a high 240 .610+ cam. what is the combustion chamber size on these heads?
With LSK lobes, it would probably be fairly "strong."
Bruce
Launching!
Joined: Feb 2006
Posts: 270
Likes: 0
Originally Posted by skipperbisket
you consider a 224/228 cam a "strong" cam? i wanna see what these heads do with a real cam, like a high 240 .610+ cam. what is the combustion chamber size on these heads?
64cc, I believe.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Banned
Joined: Aug 2005
Posts: 154
Likes: 0
From: ohio
Originally Posted by DavidNJ
Other than the flow number, I'm interested in the combustion. Some other TF heads, the Ford 'R's come to mind, have the plug seriously pointed toward the exhaust.
So more than the flow bench, I'd really like to see the results of these heads with a strong cam, like 224/228 LSK, and good intake. I'd really like to see the spark advance numbers, and maybe the amount of compression that could be tolerated.
Mike@TEA could chime in, do you expect these heads to require less advance and use more compression?
So more than the flow bench, I'd really like to see the results of these heads with a strong cam, like 224/228 LSK, and good intake. I'd really like to see the spark advance numbers, and maybe the amount of compression that could be tolerated.
Mike@TEA could chime in, do you expect these heads to require less advance and use more compression?
Originally Posted by Mike@TEA
In the initial dyno testing results I have seen the head likes about 2 degrees less timing than our LS-6 heads, our 1.5-5.3's or the AFR 205's. As for compression increases I would not expect to be able to run alot more but the shallower valve angle should tolerate some.
what was the outcome on the dyno on the head comparo
LS-6 , AFR , 1.5-5.3's vs the TFS ?
Seems like a bunch of smoke and mirrors. I hate when folks bring up product development 6-12 months before the product comes out. And right before it actually hits the market, there is always some sort of catastrophic set back.
Brandon
Brandon
Banned
Joined: Aug 2005
Posts: 154
Likes: 0
From: ohio
Originally Posted by DavidNJ
Mike, could you post a picture of the combustion chamber?
Also, TF lists the spring pocket at 1.45. Can it be cut for a 1.59 (like a Comp 26055 or 26095)?
Also, TF lists the spring pocket at 1.45. Can it be cut for a 1.59 (like a Comp 26055 or 26095)?
Originally Posted by Mike@TEA
Here is a picture of the chamber nothing really new there. As for the spring pockets it should be no problem to cut them for the larger 1.55-1.625" roller springs. I was hoping some of the guys who we have shipped them to would post some pix or results but none have yet. I am told there is a huge batch of heads in process right now and availability should be very good in the next few weeks. We flew through the first batch pretty quickly. I will post power numbers soon.
Mike,
I will post up some pictures this weekend of the Trick Flow heads. I would have posted them earlier by my digital camera is on vacation with my wife.
I will start a new post with them in it.
I can tell you all that the heads are beautiful! The CNC work and attention to detail is some the best I have ever seen.
John
Last edited by JNorris; Jun 2, 2006 at 01:05 PM.
