Generation III Internal Engine 1997-2006 LS1 | LS6
Sponsored by:
Sponsored by:

What Et's Should this Setup Deliver

Thread Tools
 
Search this Thread
 
Old 09-25-2007, 01:49 PM
  #1  
TECH Apprentice
Thread Starter
 
noah89's Avatar
 
Join Date: Feb 2002
Location: Chicago; South Side
Posts: 364
Likes: 0
Received 0 Likes on 0 Posts

Default What Et's Should this Setup Deliver

I can't drive for crap. Assuming I put MT ET Street Radials on, what ET could you achieve with this car? All mods are listed in the sig. Thanks.
Old 09-25-2007, 04:02 PM
  #2  
TECH Fanatic
iTrader: (12)
 
TheLS1Kid's Avatar
 
Join Date: Oct 2006
Location: Orlando, FL
Posts: 1,724
Likes: 0
Received 0 Likes on 0 Posts

Default

Looks like you have a nice suspension setup. Those 4.11's will really help out also.

Since you say you can't drive for **** I'd say a low 12.

If you hooked up real well a high 11 should be possible.
Old 09-25-2007, 04:09 PM
  #3  
Teching In
iTrader: (1)
 
'92 CAMARO RS's Avatar
 
Join Date: Feb 2005
Posts: 20
Likes: 0
Received 0 Likes on 0 Posts
Default

if you have radials on...with all your suspension u should put down an awesome time
Old 09-25-2007, 11:27 PM
  #4  
TECH Enthusiast
iTrader: (29)
 
Evans752's Avatar
 
Join Date: Jan 2005
Location: Logan, West Virginia
Posts: 565
Likes: 0
Received 1 Like on 1 Post

Default

11.80 to 12.00 with a decent prep track and the MT tires your talking about. Im goign off of the HP numbers at that to have posted on the bottom because my old set up put down 387HP on the dyno and I went 11.72 on DR. Good Luck
Old 09-26-2007, 12:14 PM
  #5  
TECH Resident
iTrader: (6)
 
1_bad_TA's Avatar
 
Join Date: Jun 2007
Posts: 783
Likes: 0
Received 0 Likes on 0 Posts
Default

12.0's with the hp and tq you have listed
Old 09-26-2007, 08:58 PM
  #6  
TECH Apprentice
Thread Starter
 
noah89's Avatar
 
Join Date: Feb 2002
Location: Chicago; South Side
Posts: 364
Likes: 0
Received 0 Likes on 0 Posts

Default

Thanks all. 11/3 is our track date. I'll post again after that. I've only had 11 runs in total. I think I need to be much more aggressive. Thanks again.
Old 09-26-2007, 09:48 PM
  #7  
TECH Fanatic
iTrader: (2)
 
o2camaross's Avatar
 
Join Date: Oct 2006
Location: slidell, LA
Posts: 1,117
Likes: 0
Received 0 Likes on 0 Posts

Default

you say you need to be more aggresive, what are you launching it at?
Old 09-27-2007, 06:22 PM
  #8  
TECH Apprentice
Thread Starter
 
noah89's Avatar
 
Join Date: Feb 2002
Location: Chicago; South Side
Posts: 364
Likes: 0
Received 0 Likes on 0 Posts

Default

I was launching at about 2200 rpms on street tires. My best 60 ft. is about 2.2.
Old 09-27-2007, 06:52 PM
  #9  
11 Second Club
iTrader: (2)
 
gruntwork's Avatar
 
Join Date: Jun 2005
Location: Maiden, NC
Posts: 268
Likes: 0
Received 0 Likes on 0 Posts

Default

MT's.... 15 psi, heat 'em real good, 5000 RPM and sidestep the clutch. Don't lift until you go through the traps or something goes boom.




All times are GMT -5. The time now is 05:26 AM.