What Pushrod length?
#2
I can shift faster than you.
iTrader: (21)
Join Date: Nov 2001
Location: Baton Rouge, LA
Posts: 5,133
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Pushrod length?
I used 7.35" with heads milled .050" and the TR230/224 cam. The basecircle on that cam is slightly smaller than that of the '02 LS6 cam.
#3
On The Tree
iTrader: (4)
Join Date: Feb 2003
Location: CT
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Pushrod length?
I don't know if you can "get away with" the stock length pushrods, But I was told by LPE that I would need the 7.35" pushrods with the GM Performance Parts Z06 heads, milled .060" and the Z06 cam.
#5
On The Tree
iTrader: (4)
Join Date: Feb 2003
Location: CT
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Pushrod length?
I'm not the guy that can answer that question, but it sounds like that's a little short. It is important to maintain the proper geometry between the lifter, pushrod and rocker. I have read that the lifter can compensate for some variation to the optimum length, but I don't know how much. Any experts out there that can answer this?
#7
Launching!
iTrader: (4)
Join Date: Aug 2002
Location: Alongwayfromhome
Posts: 224
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Pushrod length?
TO WHOMEVER MAY READ THIS THREAD:
See, this is what I was talking about when I said there ought to be a standard chart here on the website that shows what the ideal pushrod length is for a given combination.
.030 milled heads + .010 smaller base circle cam = X.XXX length pushrods
This isn't rocket science as far as general information this site should have. Hell, somebody give me the geometry and I can calculate it.
TO THE AUTHOR:
If you really want to be safe you can purchase an adjustable single pushrod that will tell you the proper length. I think Comp sells them, as do a few of the other large houses.
Follow the instructions on how to install it and measure it.
See, this is what I was talking about when I said there ought to be a standard chart here on the website that shows what the ideal pushrod length is for a given combination.
.030 milled heads + .010 smaller base circle cam = X.XXX length pushrods
This isn't rocket science as far as general information this site should have. Hell, somebody give me the geometry and I can calculate it.
TO THE AUTHOR:
If you really want to be safe you can purchase an adjustable single pushrod that will tell you the proper length. I think Comp sells them, as do a few of the other large houses.
Follow the instructions on how to install it and measure it.
Trending Topics
#9
TECH Fanatic
Re: What Pushrod length?
Stage 2 heads milled .060 / Cam 02-03 LS6 cam.
Can I get away with stock length poshrods?
Thanks
Can I get away with stock length poshrods?
Thanks
That's a lot to be removed from your heads!
__________________________________________________ _____
Quote from Jim: "Doesn't lifter preload play a part in this equation also? I read that Comp R lifters might need to be shimmed thus needing a slightly longer pushrod".
I don't think "maxeffect" has Comp R lifters. Anyway, Comp R lifters do like less preload. That is why they need the shims installed under the rocker arms. This has the same effect as using shorter rods. You don't want to install longer rods if you use the Comp R lifter [and] the shims. Installing longer rods would just cancel out the reduction in lifter preload that the shims gave you.
Ron,
#10
TECH Fanatic
Re: What Pushrod length?
Lets do the math on "maxeffect"s engine:
Stock GM pushrods are 7.385" long (not 7.40"). This 7.385" rod gives the correct lifter preload on a stock cam and head engine.
With that info in mind, lets see how you have changed things:
__________________________________________________ ___
Your stock LS1 cam had a cam centerline to lobe heal distance of .775"
The 2002 LS6 cam has a cam centerline to lobe heal distance of .748"
This means the LS6 cam has a .027" smaller cam centerline to lobe heal distance which would require a pushrod that is exactly .027" longer than the stock 7.385" It would need a new rod that is in fact 7.412" long.
Now, you milled .060" off the head. That will now reduce the rod length .060" from the new dimension of 7.412"
The rod length now becomes 7.352" (7.412 minus .060)
Thats only .002" (2 thousands) in difference from a set of 7.350" Thunder hardened rods.
Again..... Use 7.35" rods and no spacers.
Ron,
Stock GM pushrods are 7.385" long (not 7.40"). This 7.385" rod gives the correct lifter preload on a stock cam and head engine.
With that info in mind, lets see how you have changed things:
__________________________________________________ ___
Your stock LS1 cam had a cam centerline to lobe heal distance of .775"
The 2002 LS6 cam has a cam centerline to lobe heal distance of .748"
This means the LS6 cam has a .027" smaller cam centerline to lobe heal distance which would require a pushrod that is exactly .027" longer than the stock 7.385" It would need a new rod that is in fact 7.412" long.
Now, you milled .060" off the head. That will now reduce the rod length .060" from the new dimension of 7.412"
The rod length now becomes 7.352" (7.412 minus .060)
Thats only .002" (2 thousands) in difference from a set of 7.350" Thunder hardened rods.
Again..... Use 7.35" rods and no spacers.
Ron,
#12
Resident Grump
Join Date: Nov 2001
Location: Walker County Alabama
Posts: 1,050
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Pushrod length?
TO WHOMEVER MAY READ THIS THREAD:
See, this is what I was talking about when I said there ought to be a standard chart here on the website that shows what the ideal pushrod length is for a given combination.
.030 milled heads + .010 smaller base circle cam = X.XXX length pushrods
This isn't rocket science as far as general information this site should have. Hell, somebody give me the geometry and I can calculate it.
TO THE AUTHOR:
If you really want to be safe you can purchase an adjustable single pushrod that will tell you the proper length. I think Comp sells them, as do a few of the other large houses.
Follow the instructions on how to install it and measure it.
See, this is what I was talking about when I said there ought to be a standard chart here on the website that shows what the ideal pushrod length is for a given combination.
.030 milled heads + .010 smaller base circle cam = X.XXX length pushrods
This isn't rocket science as far as general information this site should have. Hell, somebody give me the geometry and I can calculate it.
TO THE AUTHOR:
If you really want to be safe you can purchase an adjustable single pushrod that will tell you the proper length. I think Comp sells them, as do a few of the other large houses.
Follow the instructions on how to install it and measure it.
There's just too many varibles to have a set rule for pushrod length.
#14
TECH Fanatic
Re: What Pushrod length?
Joe just used the term "Base Circle". You may have noticed that I did not use the term "base circle" above. Base circle is actually the distance across the lobe (90 degrees from the highest point of the lobe). This can be measured with a set of calipers or a mic.
You need to know the base circle distance in order to get the cam centerline to lobe heal distance. In fact, the centerline to lobe heal distance is exactly 1/2 of the cam's base circle.
The cam centerline to lobe heal distance is the distance from the centerline of the cam out to the back of the lobe (opposite of the highest point on the lobe)
The cam centerline to lobe heal distance is what is important to know when you pick pushrod length, as this is where the lifter is riding when the cam is at it's lowest lift point (valve closed).
Ron,
How ya doing Joe? Haven't talked to you in a long time.......
You need to know the base circle distance in order to get the cam centerline to lobe heal distance. In fact, the centerline to lobe heal distance is exactly 1/2 of the cam's base circle.
The cam centerline to lobe heal distance is the distance from the centerline of the cam out to the back of the lobe (opposite of the highest point on the lobe)
The cam centerline to lobe heal distance is what is important to know when you pick pushrod length, as this is where the lifter is riding when the cam is at it's lowest lift point (valve closed).
Ron,
How ya doing Joe? Haven't talked to you in a long time.......
#15
On The Tree
Join Date: Oct 2002
Location: Roanoke,va
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Pushrod length?
Hes right, u know whats going to happen if u put stock length push rods in there. ur going to put every thing together, sit in ur garage and crank ur car, its going to turn over very free and its not going to start then ur going to wonder why its not starting. I will tell u why no compression, and that comes from the pushrods being to long and holding the valves open about .060s of an inch so take the tin indians advice use the 7.35 tr or comp push rods.
#16
TECH Fanatic
Re: What Pushrod length?
I included a little diagram that just shows where on the cam you would see the base circle and the centerline to lobe heal distance. As you can see, it is very easy to measure the base circle. Then just cut that number in half to get the cam's centerline to lobe heal distance.
#18
TECH Fanatic
Re: What Pushrod length?
You need the cam out of the car in order to measure it.
(Stock LS1)
Base Circle = 1.552"
Centerline to Lobe Heal Distance = 0.776"
(TR220)
Base Circle = 1.502”
Centerline to Lobe Heal Distance = 0.751” (.025” less than stock)
(Stock LS1)
Base Circle = 1.552"
Centerline to Lobe Heal Distance = 0.776"
(TR220)
Base Circle = 1.502”
Centerline to Lobe Heal Distance = 0.751” (.025” less than stock)
#19
Restricted User
iTrader: (9)
Join Date: Sep 2002
Location: Sierra Vista, AZ
Posts: 7,603
Likes: 0
Received 0 Likes
on
0 Posts
Re: What Pushrod length?
ok, if you have the TR224, and its CtoH D of .751, and you use .030 milled heads, you come out with a 7.380 pushrod. Now with the lifter providing some cushion, is it better to use a 7.4 or 7.35? The .4 might hang the valves open, or the lifter might take up the diff, and the .35 wont open the valves all the way reducing your effective lift.
#20
TECH Fanatic
Re: What Pushrod length?
As long as the hyd lifter has [some] preload, it won't reduce the lift on the valves.
I would go with 7.35" rods. A little less preload is better than a little too much.
Too much preload will cause the lifters to pump-up at high revs.
I would go with 7.35" rods. A little less preload is better than a little too much.
Too much preload will cause the lifters to pump-up at high revs.